Cisco Systems NME-WAE manual Service-module integrated-service-engine statistics, Access router

Page 25

service-module integrated-service-engine statistics

service-module integrated-service-engine statistics

To display reset and reload information for an integrated-service-engine (ISE) network module and its IOS software, use the service-moduleintegrated-service-engine statistics command in EXEC mode.

service-module integrated-service-engine slot/unit statistics

Syntax Description

Defaults

Command Modes

Command History

slot	Slot number of the network module in the router chassis.

/unit	Number of the daughter card on the network module. For ISE network
	modules, always use 0. The slash mark (/) is required between the slot
	argument and the unit argument.

none
User EXEC
Privileged EXEC

ReleaseModification

12.4(9)T	This command was introduced for ISE network modules.

Usage Guidelines	The statistics displayed by this command represent control communication events between the network
	module and the router. For ACNS-specific statistics, access the ACNS CLI and use the show statistics
	commands documented in the Cisco Application and Content Networking System Software Command
	Reference.

Examples	The following example displays information for an ISE network module that is installed in slot 2 of an
	access router:
	Router# service-module integrated-service-engine 2/0 statistics
	Module Reset Statistics:
	CLI reset count = 1
	CLI reload count = 0
	Registration request timeout reset count = 0
	Error recovery timeout reset count = 0
	Module registration count = 2
	The last IOS initiated event was a cli reset at *13:34:33.847 UTC Sun Dec 18 2005

Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments

	OL-13140-02	25

Image 25

Contents Contents Restrictions for Cisco WAE Network Modules Prerequisites for Installing the Cisco WAE Network ModulesCisco WAE Network Module Hardware Description Hard Disk and Memory SpecificationsFaceplate and LEDs Model Hard Disk MemoryCF card ShutdownOn This Hardware Interface Configure These Settings Using ThisHardware Interfaces This section contains the following topicsSummary Steps Detailed Steps Examples Setting Up Network Module InterfacesExample Procedure CommandDisplay the router running configuration so that you can Save the router running configurationVerify interface configurations Opening and Closing a Network Module SessionPress Control-Shift-6 Press Ctrl-Shift-6 Example ConfigurationConfiguration Mode Command Purpose Accessing the Acns Software on the Network ModuleShutting Down and Starting Up Cisco WAE Network Modules Displaying Status and Diagnostic Output Command Purpose Cisco technical support for problem Service module. This information is useful toDisplays general information about DiagnosisCommand Reference Interface integrated-service-engine slot/unit Interface integrated-service-engineSyntax Description Defaults Command Modes Command History ReleaseModificationDefaults Command Modes Command History Service-module integrated-service-engine default-bootBootloader to perform startup routines None Privileged ExecService-module integrated-service-engine slot/unit reload Service-module integrated-service-engine reloadCommand Description Usage GuidelinesService-module integrated-service-engine slot/unit reset Service-module integrated-service-engine resetRelated Commands Description Router# service-module integrated-service-engine 1/0 resetCommand Description Open Service-module integrated-service-engine sessionUsername Related Commands Description Service-module integrated-service-engine slot/unit shutdown Service-module integrated-service-engine shutdownInterface integrated-service-engine Integrated-service-engine resetCommand Description Access router Service-module integrated-service-engine statisticsService-module integrated-service-engine slot/unit status Service-module integrated-service-engine statusRouter# service-module integrated-service-engine 1/0 status Display the ISE network module software release versionRelated Commands Description Show controllers integrated-service-engine slot/unit Show controllers integrated-service-engineField Description Related Commands Description Show diag slot Show diagRelease Modification Show diag subslot Field Descriptions Integrated-service-engine network modules Displays basic interface configuration information forNetwork modules Show interfaces integrated-service-engine slot/unit Show interfaces integrated-service-engineCommand Modes Command History Field Description Station that is transmitting bad data Errors created when the CRC generated by the originating LANField Description Bootloader BoothelperGlossary BladeRelated Documentation Service or servicesEngine Syslog Related Topic Document TitlePage OL-13140-02