Cisco Systems NME-WAE Show interfaces integrated-service-engine, Command Modes Command History

Page 33

show interfaces integrated-service-engine

show interfaces integrated-service-engine

To display basic interface configuration information for an integrated-service-engine (ISE) network module, use the show interfaces integrated-service-enginecommand in privileged EXEC mode.

show interfaces integrated-service-engine slot/unit

Syntax Description	slot	Slot number of the network module in the router chassis.
	/unit	Number of the daughter card on the network module. For ISE network
		modules, always use 0. The slash mark (/) is required between the slot
		argument and the unit argument.

Command Modes

Command History

Privileged EXEC

ReleaseModification

12.4(9)T	This command was introduced for ISE network modules.

Usage Guidelines Table 6 describes the fields shown in the command output.

		Table 6	show interfaces integrated-service-engine Field Descriptions

		Field		Description

		Integrated-Service-Engine		Indicates whether the ISE interface hardware is currently active.
				If the ISE interface hardware is active, the output states that
				“Integrated-Service-Engine slot/port is up.” If it has been taken
				down by an administrator, the output states that
				“Integrated-Service-Engine slot/port is administratively down.”

		line protocol		Indicates whether the software processes that handle the line
				protocol consider the line usable or whether the line has been
				taken down by an administrator.

		Hardware address		Hardware type and address.

		Internet address		IP address.

		MTU		Maximum transmission unit (MTU) of the
				integrated-service-engine interface.

		BW		Bandwidth of the interface, in kilobits per second.

		DLY		Delay of the interface, in microseconds.

		reliability		Reliability of the interface as a fraction of 255 (255/255 is
				100-percent reliability), calculated as an exponential average over
				5 minutes.

		txload		Transmit load on the interface as a fraction of 255 (255/255 is
				completely saturated), calculated as an exponential average over
				5 minutes.

			Configuring Cisco Access Routers and the NME-WAE Network Module for ACNS Deployments


	OL-13140-02					33
	OL-13140-02					33

Image 33

Contents Contents Restrictions for Cisco WAE Network Modules Prerequisites for Installing the Cisco WAE Network ModulesCisco WAE Network Module Hardware Description Hard Disk and Memory SpecificationsFaceplate and LEDs Model Hard Disk MemoryCF card ShutdownOn This Hardware Interface Configure These Settings Using ThisHardware Interfaces This section contains the following topicsSummary Steps Detailed Steps Examples Setting Up Network Module InterfacesExample Procedure CommandDisplay the router running configuration so that you can Save the router running configurationVerify interface configurations Opening and Closing a Network Module SessionPress Control-Shift-6 Press Ctrl-Shift-6 Example ConfigurationAccessing the Acns Software on the Network Module Configuration Mode Command PurposeShutting Down and Starting Up Cisco WAE Network Modules Displaying Status and Diagnostic Output Command Purpose Cisco technical support for problem Service module. This information is useful toDisplays general information about DiagnosisCommand Reference Interface integrated-service-engine slot/unit Interface integrated-service-engineSyntax Description Defaults Command Modes Command History ReleaseModificationDefaults Command Modes Command History Service-module integrated-service-engine default-bootBootloader to perform startup routines None Privileged ExecService-module integrated-service-engine slot/unit reload Service-module integrated-service-engine reloadCommand Description Usage GuidelinesService-module integrated-service-engine slot/unit reset Service-module integrated-service-engine resetRelated Commands Description Router# service-module integrated-service-engine 1/0 resetCommand Description Service-module integrated-service-engine session OpenUsername Related Commands Description Service-module integrated-service-engine slot/unit shutdown Service-module integrated-service-engine shutdownInterface integrated-service-engine Integrated-service-engine resetCommand Description Access router Service-module integrated-service-engine statisticsService-module integrated-service-engine slot/unit status Service-module integrated-service-engine statusRouter# service-module integrated-service-engine 1/0 status Display the ISE network module software release versionRelated Commands Description Show controllers integrated-service-engine Show controllers integrated-service-engine slot/unitField Description Related Commands Description Show diag Show diag slotRelease Modification Show diag subslot Field Descriptions Displays basic interface configuration information for Integrated-service-engine network modulesNetwork modules Show interfaces integrated-service-engine Show interfaces integrated-service-engine slot/unitCommand Modes Command History Field Description Station that is transmitting bad data Errors created when the CRC generated by the originating LANField Description Bootloader BoothelperGlossary BladeRelated Documentation Service or servicesEngine Syslog Related Topic Document TitlePage OL-13140-02