Graco 833 important safety instructions Troubleshooting, Problem Cause Solution

Page 29

 

 

Troubleshooting

 

Troubleshooting

 

 

 

 

PROBLEM

CAUSE

SOLUTION

 

 

 

 

 

 

Gas engine pulls hard (won't start)

Hydraulic pressure is too high

Turn hydraulic pressure knob

 

 

counterclockwise to lowest setting

Gas engine does not start

Switch OFF, low oil, no gasoline

Consult engine manual, supplied

Gas engine doesn't work properly

Faulty engine

Consult engine manual, supplied

Gas engine operates, but

Pump valve is OFF

Set pump valve ON

displacement pump doesn't operate

Pressure setting too low

Increase pressure, page 12

 

Displacement pump outlet filter

Clean the filter

 

(if used) is dirty or clogged

 

 

Tip or tip filter (if used) is clogged

Remove tip and/or filter and clean

 

Hydraulic fluid too low

Shut off sprayer. Add fluid*

 

Belt worn, broken or off

Replace. See manual 311283

 

Hydraulic pump worn or damaged

Bring sprayer to Graco distributor for

 

 

repair

 

Dried paint seized paint pump rod

Service pump. See manual 311485

 

Hydraulic motor not shifting

Set pump valve OFF. Turn pressure

 

 

down. Turn engine OFF. Pry rod up

 

 

or down until hydraulic motor shifts.

 

 

Manual 311283

Displacement pump operates, but

Piston ball check not seating properly

Service piston ball check.

output is low on upstroke

 

See manual 311485

 

Piston packings worn or damaged

Replace packings. See manual

 

 

311485

Displacement pump operates but

Piston packings worn or damaged

Tighten packing nut or replace

output is low on downstroke and/or

 

packings. See manual 311485

on both strokes

Intake valve ball check not seating

Service intake valve ball check.

 

properly

See manual 311485

 

Suction tube air leak

 

Paint leaks and runs over side of

Loose wet-cup

Tighten wet-cup enough to stop

wetcup

 

leakage

 

Throat packings worn or damaged

Replace packings.

 

 

See manual 311485

Excessive leakage around hydraulic

Piston rod seal worn or damaged

Replace these parts.

motor piston rod wiper

 

See manual 311283

Fluid delivery is low

Pressure setting too low

Increase pressure, page 4

 

Displacement pump outlet filter (if

Clean filter

 

used) is dirty or clogged

 

 

Intake line to pump inlet is not tight

Tighten

 

Hydraulic motor is worn or damaged

Bring sprayer to Graco distributor

 

 

for repair

 

Large pressure drop in fluid hose

Use larger diameter or shorter hose

311279F

29

Image 29
Contents 311254 311283 311484 311485 Skin Injection Hazard Fire and Explosion HazardPressurized Equipment Hazard Recoil HazardMoving Parts Hazard Equipment Misuse HazardPressurized Aluminum Parts Hazard Suction HazardRisques D’INCENDIE ET D’EXPLOSION Mise en gardeRisques DUS AUX Pièces EN Aluminium Sous Pression Risque EN CAS DE Mauvaise Utilisation DU MatérielRisques DE Brûlure Équipement DE Protection DU PersonnelPeligro DE Incendios Y Explosiones AdvertenciaPeligro DE Inyección a Través DE LA Piel Peligros DEL Equipo a PresiónPeligro DE Piezas EN Movimiento Peligros Debidos a LA Utilización Incorrecta DEL EquipoPeligro DE Piezas DE Aluminio a Presión Peligro DE AspiraciónBRAND- UND Explosionsgefahr WarnungGefahr Durch Materialeinspritzung Gefahr Durch Druckbeaufschlagtes GerätGefahr Durch Bewegliche Teile Gefahr Durch Missbräuchliche GeräteverwendungGefahr Durch Druckbeaufschlagte Aluminiumteile Gefahr Durch Starken SOGBRAND- EN Explosiegevaar WaarschuwingGevaar Voor Injectie Door DE Huid Gevaar VAN Apparatuur Onder DrukGevaren VAN Bewegende Delen RISICO’S BIJ Verkeerd Gebruik VAN DE ApparatuurGevaren VAN Aluminium Onderdelen Onder Druk Gevaar Door AanzuigingMotors Elektrostart Motor Elektrische start One strap secured across Pressure Relief Complete Setup Setup / Réglage / Ajuste / Einrichtung / OpstellenComplete Setup Safe Range cold Ti7108a Start engine Mettre la vanne de pompe Increase pressure enough Instale la boquilla SwitchTip and Guard Assembly Clearing Tip Clogs OFF Cleanup / Nettoyage / Limpieza / Reinigung / Reinigen Marche Ti20967a Ti5261a Pump Armor Problem Cause Solution TroubleshootingProblem Cause Solution Guide de dépannage Problème Cause SolutionProblème Cause Solution Localización de averías Problema Causa SoluciónProblema Causa Solución Fehlersuche Problem Ursache LösungFehlersuche Probleem Oorzaak Oplossing Storingen opsporen en verhelpenProbleem Oorzaak Oplossing Sprayer Technical DataPulvérisateur Caractéristiques techniquesPulverizador Características técnicasSpritzgerät Technische DatenSpuittoestel Technische gegevens311279F Graco Information Warranty / Garantie / Garantía / Garantie / GarantieVan

833 specifications

The Graco 833 is a powerful and versatile airless paint sprayer designed for professionals and DIY enthusiasts alike. This machine is specifically engineered to deliver high-quality finishes on a wide variety of surfaces, making it an invaluable tool for painting, staining, and sealing projects.

One of the standout features of the Graco 833 is its powerful motor, which provides consistent pressure and enables a smooth spray pattern. The machine is capable of handling thick materials, which means it can be used for both oil-based and latex paints without any issues. Its robust construction ensures durability and longevity, even under heavy use.

The Graco 833 comes equipped with a patented ProConnect system that allows for quick and easy pump replacement. This feature significantly reduces downtime, enabling users to maintain productivity on the job. Additionally, the easy-to-follow design of the sprayer allows for fast set-up and clean-up, making it user-friendly for both experienced painters and novices.

Another important characteristic is the adjustable pressure control, which gives users the ability to customize the sprayer’s output based on the specifics of their project. This feature is particularly useful for achieving different spray patterns and finishes, from fine details to larger areas. The integrated pressure gauge allows users to monitor settings in real-time, ensuring optimal performance throughout the painting process.

The Graco 833 also benefits from smart technology that improves efficiency and reduces waste. The machine is designed to minimize over-spray, which not only conserves paint but also leads to cleaner, more professional results. The sprayer is compatible with a range of spray tips, allowing for easy interchangeability and versatility in application techniques.

Furthermore, the lightweight and portable design of the Graco 833 makes it easy to transport and maneuver on job sites. This feature is especially beneficial for exterior painting projects where accessibility can be a challenge.

In summary, the Graco 833 is a reliable and efficient airless paint sprayer that combines advanced technology with user-friendly features. Its power, durability, and versatility make it an ideal choice for anyone looking to achieve professional-quality finishes in their painting projects. Whether you are a seasoned contractor or a weekend warrior, the Graco 833 is designed to meet your needs and exceed your expectations, delivering exceptional results every time.