Black & Decker FS6500HD, FS6000FD, FS7000D, FS8000HD instruction manual Specific Safety Rules

Page 3

635040-03 FS drills 4/25/06 1:56 PM Page 3

b)Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c)Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d)Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

e)Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f)Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g)Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5)Service

a)Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY RULES

a)Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.

b)Use clamps or another practical way to secure and support the work piece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

c)Wear ear protectors with impact drills. Exposure to noise can cause hearing loss.

d)Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.

e)Hammer bits and tools get hot during operation. Wear gloves when touching them.

WARNING: ALWAYS use safety glasses. Everyday eye glasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

ANSI Z87.1 eye protection (CAN/CSA Z94.3)

ANSI S12.6 (S3.19) hearing protection

NIOSH/OSHA/MSHA respiratory protection

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.

3

Image 3
Contents VEA EL Español EN LA Contraportada Drills and Hammer DrillsGeneral Safety Rules Specific Safety Rules Functional Description 25/06 156 PM Motor Safety Warnings and Instructions DrillsFast Drive Bit Change System FS6000FD AssemblyInserting a drill bit or other accessory fig. B & C Removing and attaching the chuck fig. D, E, F, GSelecting the direction of rotation FS7000D, FS8000HD Selecting the drilling mode FS6500HD, FS8000HD fig. HOperating Instructions Selecting the direction of rotation FS6000FD, FS6500HDDrilling Setting the drilling depth FS6500HD, FS8000HDSwitching on and off Two-gear selector FS8000HD figService Information Full TWO-YEAR Home USE Warranty TroubleshootingProblem Possible Cause Possible Solution MaintenanceCovered Under OUR Warranty Special Warranty Note to ContractorsNuméro de catalogue FS7000D illustré Guide D’UTILISATIONConserver CES Directives Règles de sécurité généralesToujours Porter UN Équipement DE Protection Homologué Règles DE Sécurité SpécifiquesRallonges Description Fonctionnelle FS drills 4/25/06 156 PM Avertissements de sécurité et directives perceuses AssemblageMoteur Mandrin et clé modèle FS7000D fig. C Insérer une mèche ou un autre accessoire fig. B et CRetrait et fixation du mandrin fig. D, E, F, G Modèle FS6500HD, FS8000HDMandrin sans clé modèles FS6500HD, FS8000HD fig. F FonctionnementSélection du sens de rotation modèles FS6000FD, FS6500HD Sélection du sens de rotation modèles FS7000D, FS8000HDSélecteur à double marche modèle FS8000HD fig Mise en marche et arrêtPerçage 25/06 156 PM Présente Garantie AccessoiresEntretien Information SUR LES RéparationsCapacités Maximales Recommandées Número de catálogo exhibido FS7000D Manual DE InstruccionesConserve Estas Instrucciones Normas generales de seguridadNormas DE Seguridad Específicas Capacidad nominal en amperios Cables prolongadoresDescripción DE FS drills 4/25/06 157 PM Instrucciones y advertencias de seguridad Taladros EnsamblajeFS6500HD, FS8000HD Sistema de cambio de brocas Fast Drive FS6000FD Inserción de una broca u otro accesorio figuras B y CAcoplamiento y extracción del portabrocas fig. D, E, F, G Portabrocas y llave FS7000D fig. CPortabrocas con llave FS7000D fig. G Instrucciones de operaciónSelección de la dirección de rotación FS6000FD, FS6500HD Portabrocas sin llave FS6500HD, FS8000HD fig. FAjuste de la profundidad de perforación FS6500HD, FS8000HD Selección de la dirección de rotación FS7000D, FS8000HDSelección del modo de taladrado FS6500HD, FS8000HD fig. H Selector de dos engranajes FS8000HD figTaladrado en metal Taladrado en maderaMantenimiento Problema Causa posible Solución posibleNota Especial DE Garantía Para Contratistas Capacidades Máximas RecomendadasMONTERREY, N.L CULIACAN, SINMEXICO, D.F MERIDA, YUCFS drills 4/25/06 157 PM FS drills 4/25/06 157 PM