Black & Decker FS6000FD, FS7000D, FS8000HD, FS6500HD instruction manual Functional Description

Page 4

635040-03 FS drills 4/25/06 1:56 PM Page 4

The label on your tool may include the following symbols.
V			volts	A			amperes
Hz			hertz	W			watts
min			minutes			......................	alternating
				no			current
			direct current				no load speed
			direct current				no load speed
	..........................		Class II Construction			........................	earthing terminal


	........................		safety alert symbol	.../min			revolutions or
							reciprocations
bpm			beats per minute				per minute
bpm			beats per minute

Extension Cords

When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

			Minimum Gage for Cord Sets
Volts			Total Length of Cord in Feet
120V			0-25	26-50	51-100 101-150
240V			0-50	51-100	101-200	201-300
Ampere Rating
More		Not more		American Wire Gage
Than		Than
0	-	6	18	16	16	14
6	-	10	18	16	14	12
10	-	12	16	16	14	12
12	-	16	14	12	Not Recommended

FUNCTIONAL DESCRIPTION

1. Variable speed switch

FS6000FD

11

12 10

FS6500HD

	5
	8
6	3
	3

2.	Lock-on button
3.	Forward/reverse slider
4. Two-gear selector
5.	Drilling mode selector
6. Chuck

	3
1	2
1

1

2

9

7. Chuck key

8. Depth stop

9. Side handle

10. Belt clip

11. Fast drive remov. chuck

12. Bit storage

FS7000D 10

6

3

1	2
1
9
	7

FS8000HD

5

3

6

4

1 2

9

12

4

Image 4

Contents Drills and Hammer Drills VEA EL Español EN LA ContraportadaGeneral Safety Rules Specific Safety Rules Functional Description 25/06 156 PM Safety Warnings and Instructions Drills MotorAssembly Inserting a drill bit or other accessory fig. B & CRemoving and attaching the chuck fig. D, E, F, G Fast Drive Bit Change System FS6000FDSelecting the drilling mode FS6500HD, FS8000HD fig. H Operating InstructionsSelecting the direction of rotation FS6000FD, FS6500HD Selecting the direction of rotation FS7000D, FS8000HDSetting the drilling depth FS6500HD, FS8000HD Switching on and offTwo-gear selector FS8000HD fig DrillingTroubleshooting Problem Possible Cause Possible SolutionMaintenance Service Information Full TWO-YEAR Home USE WarrantySpecial Warranty Note to Contractors Covered Under OUR WarrantyGuide D’UTILISATION Numéro de catalogue FS7000D illustréRègles de sécurité générales Conserver CES DirectivesRègles DE Sécurité Spécifiques Toujours Porter UN Équipement DE Protection HomologuéRallonges Description Fonctionnelle FS drills 4/25/06 156 PM Assemblage Avertissements de sécurité et directives perceusesMoteur Insérer une mèche ou un autre accessoire fig. B et C Retrait et fixation du mandrin fig. D, E, F, GModèle FS6500HD, FS8000HD Mandrin et clé modèle FS7000D fig. CFonctionnement Sélection du sens de rotation modèles FS6000FD, FS6500HDSélection du sens de rotation modèles FS7000D, FS8000HD Mandrin sans clé modèles FS6500HD, FS8000HD fig. FMise en marche et arrêt Sélecteur à double marche modèle FS8000HD figPerçage 25/06 156 PM Accessoires EntretienInformation SUR LES Réparations Présente GarantieCapacités Maximales Recommandées Manual DE Instrucciones Número de catálogo exhibido FS7000DNormas generales de seguridad Conserve Estas InstruccionesNormas DE Seguridad Específicas Cables prolongadores Capacidad nominal en amperiosDescripción DE FS drills 4/25/06 157 PM Ensamblaje Instrucciones y advertencias de seguridad TaladrosFS6500HD, FS8000HD Inserción de una broca u otro accesorio figuras B y C Acoplamiento y extracción del portabrocas fig. D, E, F, GPortabrocas y llave FS7000D fig. C Sistema de cambio de brocas Fast Drive FS6000FDInstrucciones de operación Selección de la dirección de rotación FS6000FD, FS6500HDPortabrocas sin llave FS6500HD, FS8000HD fig. F Portabrocas con llave FS7000D fig. GSelección de la dirección de rotación FS7000D, FS8000HD Selección del modo de taladrado FS6500HD, FS8000HD fig. HSelector de dos engranajes FS8000HD fig Ajuste de la profundidad de perforación FS6500HD, FS8000HDTaladrado en madera Taladrado en metalProblema Causa posible Solución posible MantenimientoCapacidades Máximas Recomendadas Nota Especial DE Garantía Para ContratistasCULIACAN, SIN MEXICO, D.FMERIDA, YUC MONTERREY, N.LFS drills 4/25/06 157 PM FS drills 4/25/06 157 PM