Bosch Power Tools 1375A Power Tool Safety Rules, Work Area, Electrical Safety, Personal Safety

Page 2

BM 1619P01046 5-05 5/10/05 10:39 PM Page 2

Power Tool Safety Rules

!WARNING Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

Work Area

Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

Keep by-standers, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

Electrical Safety

Double Insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double Insulation eliminates the need for the three wire grounded power cord and grounded power supply system. Before plugging in the tool, be certain the outlet voltage supplied is within the voltage marked on the nameplate. Do not use “AC only” rated tools with a DC power supply.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. If operating the power tool in damp locations is unavoidable, a Ground Fault Circuit Interrupter must be used to supply the power to your tool. Electrician’s rubber gloves and footwear will further enhance your personal safety.

Don't expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W." These cords are rated for outdoor use and reduce the risk of electric shock. Refer to “Recommended sizes of Extension Cords” in the Accessory section of this manual.

Personal Safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Keep handles dry, clean and free from oil and grease.

Avoid accidental starting. Be sure switch is “OFF” before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch “ON” invites accidents.

Remove adjusting keys or wrenches before turning the tool “ON”. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

Tool Use and Care

Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

-2-

Image 2
Contents Call Toll Free For EnglishSee For Consumer InformationPersonal Safety Power Tool Safety RulesElectrical Safety Work AreaAngle Grinder Safety Rules ServiceBurst and the fragments strike you or bystanders Symbols Measures reduce the risk of starting the tool accidentally Functional Description and SpecificationsAngle Grinders ToolWheel Guard Installation AssemblyDisc Grinding Wheel Assembly Lock NUT and Backing FlangeMasonry Cutting Wheel Assembly Sanding Accessories AssemblySanding Operations Operating InstructionsGrinding Operations Sanding Wood Wire Brush OperationsSanding Tips Sanding MetalCleaning MaintenanceAccessories Sécurité électrique Règles de Sécurité GénéralesAire de travail Sécurité des personnesConsignes de sécurité de la rectifieuse dangle RéparationLe plomb provenant des peintures à base de plomb Symboles Outil Description fonctionnelle et spécificationsRectifieuses d’angles Numéro de modèlePose DU Protecteur AssemblageEnsemble de meule à disque Écrou DE Blocage ET Bride D’APPUIDisque D’APPUI Ensemble daccessoires de ponçageEnsemble de meule pour coupe de maçonnerie Ensemble DE Brosse MétalliqueTravaux de ponçage Consignes de fonctionnementTravaux de meulage Ponçage DES Métaux Travaux à la brosse métalliquePonçage DU Bois Lubrification DE L’OUTIL EntretienNettoyage Balais OU CharbonsSeguridad eléctrica Normas de seguridad para herramientas mecánicasArea de trabajo Seguridad personalNormas de seguridad para amoladoras angulares ServicioBM 1619P01046 5-05 5/10/05 1039 PM De Ni-Cd SímbolosCon aislamiento doble Herramienta Descripción funcional y especificacionesAmoladoras angulares Capacidades máximasMango Lateral EnsamblajeEnsamblaje de la rueda de amolar de disco Instalacion DEL Protector DE LA MuelaZapata DE Soporte Ensamblaje de la rueda de corte de MamposteríaEnsamblaje de los accesorios de lijar EL Disco DE LijarOperaciones de lijado Instrucciones de funcionamientoOperación de amolado Si el disco accesorio se Operaciones con escobillas de alambreConsejos Para Lijar Lijado DE MaderaLimpieza MantenimientoAccesorios Limited Warranty of Bosch Portable and Benchtop Power Tools
Related manuals
Manual 39 pages 43.46 Kb