Bostitch LHF2025K, EHF1838K manual Tool Operation Check, Maintainingthe Pneumatictool

Page 9

TOOL OPERATION CHECK

CAUTION: Remove all fasteners from tool before performing tool operation check.

SEQUENTIAL TRIP OPERATION:

A. Press the contact trip against the work surface, without touching the trigger.

THE TOOL MUST NOT CYCLE.

B. Hold the tool off the work surface and pull the trigger.

THE TOOL MUST NOT CYCLE.

Release the trigger. The trigger must return to the trigger stop on the frame.

C. Pull the trigger and press the contact trip against the work surface.

THE TOOL MUST NOT CYCLE.

D. With finger off the trigger, press the contact trip against the work surface. Pull the trigger.

THE TOOL MUST CYCLE.

MAINTAININGTHE PNEUMATICTOOL

When working on air tools, note the warnings in this manual and use extra care evaluating problem tools.

CAUTION: Pusher spring (constant force spring). Caution must be used when working with the spring assembly.The spring is wrapped around, but not attached to, a roller. If the spring is extended beyond its length, the end will come off the roller and the spring will roll up with a snap, with a chance of pinching your hand. Also the edges of the spring are very thin and could cut. Care must also be taken to insure no permanent kinks are put in the spring as this will reduce the springs force.

REPLACEMENT PARTS:

Use only genuine BOSTITCH replacement parts. Do not use modified parts.

ASSEMBLY PROCEDURE FOR SEALS:

When repairing a tool, make sure the internal parts are clean and lubricated. Use Parker “O”-LUBE, Magnalube, or equivalent on all “O”-rings. Coat each “O”-ring with lubricant before assembling.

AIR SUPPLY-PRESSURE AND VOLUME:

Air volume is as important as air pressure. The air volume supplied to the tool may be inadequate because of undersize fittings and hoses, or from the effects of dirt and water in the system. Restricted air flow will prevent the tool from receiving an adequate volume of air, even though the pressure reading is high. The results will be slow operation, misfeeds or reduced driving power. Before evaluating tool problems for these symptoms, trace the air supply from the tool to the supply source for restrictive connectors, low points containing water and anything else that would prevent full volume flow of air to the tool.

-9-

Image 9
Contents EHF1838K & LHF2025K Index IntroductionAIR Supply and Connections Safety InstructionsLoadingtool OperationTool Components Fastener Specifications Tool SpecificationsOperating Pressure Air ConsumptionAIR Supplyand Connections Loading the EHF1838K & LHF2025K Loadingthe EHF1838K & LHF2025KTool Operation Before Handling or Operating this ToolSequential Trip Maintainingthe Pneumatictool Tool Operation CheckTroubleshooting ProblemCausecorrection Maintenance Benefit Procedure Service Interval Maintenance ChecklistMiiifs Other Bostitch Flooring ProductsIntroducción ÍndiceNota Suministro DE Airey Conexiones Instrucciones DE SeguridadCarga DE LA Herramienta FuncionamientoComponentes DE LA Herramienta Especificaciones DE Fijaciones Especificaciones DE LA HerramientaPresión operativa Consumo de aireMangueras ConectoresFuente DE Suministro ReguladorCarga DE LA EHF1838K & LHF2025K Carga DE LA EHF1838K Y LA LHF2025KOperación DE LA Herramienta OperaciónFuncionamiento DEL Disparo Secuencial Revisión Funcional DE LA Herramienta Presión Y Volumen DEL Suministro DE AireMantenimiento DE LA Herramienta Neumática Piezas DE RepuestoProblema Causa Solución DE ProblemasMantenimiento Beneficio Procedimiento Intervalo De servicio Lista DE Verificación DE MantenimientoOtros Productos Bostitch Para Pisos Garantie Limitée É.-U. et Canada seulement RemarqueAlimentation Dair ET Connexions Consignes DE SécuritéChargement DE L’OUTIL FonctionnementComposants DE Loutil Caractéristiques DES Attaches Spécifications DE L’OUTILPression de fonctionnement Consommation d’airTuyauxsouples RaccordsSource D’ALIMENTATION RégulateurChargement DE LA EHF1838K & LHF2025K Chargement DE LA EHF1838K ET DE LA LHF2025KMode DE Déclenchement Fonctionnement EN Mode Déclenchement SéquentielFonctionnement DE L’OUTIL Vérification DU Fonctionnement DE L’OUTIL Alimentation DAIR-PRESSION ET VolumeEntretien DE L’OUTILPNEUMATIQUE Pièces DE RechangeCausesolution DépannageProblème Liste DE Vérification Pour L’ENTRETIEN Entretien Bienfait Procédure Intervalle De serviceAutres Produits Bostitch Pour Planchers