Elation Professional 575H manual Fixture Menu, Default settings shaded

Page 25

Design Par 575H™

10. FIXTURE MENU

On-Board System Menu: The DESIGN PAR 575H™ comes with an easy to navigate system menu. This next section will detail the functions of each command in the system menu.

LED Control Panel: The control panel located on the top, front of the fixture allows you to access the main menu and make all necessary adjustments to the Design Par 575H™. During normal operation, tapping the “MODE/ESC” key once will access the fixture’s main menu. Once in the main menu you can navigate through the different functions and access the sub-menus with the Up and Down buttons. Once you reach a field that requires adjusting, tap the ENTER button to activate that field and use the UP and Down button to adjust the field. Tapping the Enter button once more will confirm your setting. Once a setting is saved the LED will briefly readout PASS to confirm a new setting has been made and locked into memory. You may exit the main menu at any time without making any adjustments by tapping the MODE/ESC button.

MODE/ESC Button - To access the main menu locate the MODE/ESC button on the front of the unit. Press this button to activate the system menu. Tap the UP button until you reach the function you wish to change. When you reach the function you wish to change tap the ENTER button once to select that menu function. When a function is selected the menu will begin to flash, use the UP or DOWN button to change the function. Once your changes are made tap the ENTER button yet again to lock the change in the system menu. To exit without making any changes tap the MODE/ESC button.

Default settings shaded.

 

 

 

 

 

 

 

 

Indicate the staring DMX address

0

ADDR

AXXX

A001

 

 

 

 

 

 

 

 

A001 also is the setting for slave

 

 

 

 

 

 

 

 

1

TEST

T-01~T-XX

 

 

 

 

Automatically test the function

 

 

RUN

 

 

MSTR/ALON

Runs fixture as “master” or “alone”

 

 

 

 

for auto

2

PLAY

 

 

 

 

 

 

AUDI

 

 

MSTR/ALON

Runs fixture as “master” or “alone”

 

 

 

 

for audio

 

 

 

 

 

 

 

 

 

 

AUTO

 

 

OFF

/ RUN /AUDI

Runs fixture for no DMX

 

 

 

 

 

 

 

 

 

©Elation Professional®

25

Design Par 575H™

Image 25
Contents Design Par 575H Contents General Information Never open this fixture while in use Design Par 575H Safety Instructions Design Par 575H Features General Guidelines Fixture Overview Design Par 575H Design Par 575H Installing or replacing the lamp Lamp Installation InstructionsLamp Optimization Design Par 575H Mounting Mounting and InstallationMounting points Clamp Mounting Securing the Design PAR 575H Understanding DMX DMX-512 connection with DMX terminator DMX-512 control connectionFixture DMX addressing Design Par 575H Display LED Indicators Fixture Menu Default settings shadedLamp OFF Main Menu Functions Setting/Changing the DMX AddressAddress Menu Test MenuAudi Play Menu RUNAuto Lamp Menu Rese Reset MenuALL ScanLife Time MenuLamp ClmpRtlt Menu Rpan MenuFine Menu MIC Menu Degr MenuDisplay Menu Laau Automatic lamp start with power Laau Fixture SettingsRdmx Dlof Controller SettingsDlay Spot Reload the original factory settingsDfse Fans FeedVER Edit Menu AdjuStep RECSC01 RUN Design Par 575H DMX Channel Traits DMX channel function and values Error Codes Design Par 575H Disconnect from mains before starting maintenance operation Cleaning and MaintenanceYear Limited Warranty Design Par 575H Photometric Data Dimensional Drawings Circuit Schematic Power supply Power consumption Technical SpecificationsDesign Par 575H Elation Professional Design Par 575H Elation Professional Elation Professional