Grizzly G0656X manual Foreword, Contact Info

Page 18

INTRODUCTION

Foreword

We are proud to offer the Model G0656 8" Jointer with Built-In Mobile Base. This machine is part of a growing Grizzly family of fine woodworking machinery. When used according to the guide- lines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satis- faction.

The specifications, drawings, and photographs illustrated in this manual represent the Model G0656 when the manual was prepared. However, owing to Grizzly’s policy of continuous improve- ment, changes may be made at any time with no obligation on the part of Grizzly.

For your convenience, we always keep current Grizzly manuals available on our website at www. grizzly.com. Any updates to your machine will be reflected in these manuals as soon as they are complete. Visit our site often to check for the lat- est updates to this manual!

-2-

Contact Info

If you have any comments regarding this manual, please write to us at the address below:

Grizzly Industrial, Inc.

C/O Technical Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: manuals@grizzly.com

We stand behind our machines. If you have any service questions or parts requests, please call or write us at the location listed below.

Grizzly Industrial, Inc.

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone: (570) 546-9663

Fax: (800) 438-5901

E-Mail: techsupport@grizzly.com

Web Site: http://www.grizzly.com

G0656 8" Jointer with Built-In Mobile Base

Image 18

Contents Machine Inventory Setting Outfeed Table Height Wood Crate QtyTo set the outfeed table height Replacing Carbide Inserts Tools Needed QtyTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Table Parts Breakdown Table Parts List DescriptionFence Parts Breakdown Fence Parts List Stand Parts Breakdown Stand Parts List Label Placement Assembly See Follow Steps 1-14 on Pages 14 Assembly Fasteners QtyClean Up See Machine Inventory SeeHandwheels installed Perform Steps 18-26 on Pages 15Model G0656 Page Table of Contents Foreword Contact InfoMachine Data Sheet G0656 8 Jointer with Built-In Mobile Base Identification Safety Instructions for Machinery G0656 8 Jointer with Built-In Mobile Base Additional Safety Instructions for Jointers Full Load Amperage Draw Power Connection Device220V Operation Minimum Circuit RequirementsUnpacking Setup SafetyItems Needed for Setup Description QtyInventory Cardboard Box Figure QtyHardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadAssembly To assemble the jointerChecking belt alignment Cutterhead Pulley Motor Page Dust Collection Setting Outfeed To connect a dust collection hoseTest Run Recommended AdjustmentsFactory adjustments that should be verified Tighten V-BeltOperation Safety Jointer Overview OperationsBasic Controls Start Button Starts motorStock Inspection Requirements Scrape all glue off of boards before joint- ingSquaring Stock Surface PlaningEdge Jointing To surface plane on the jointerBevel Cutting To edge joint on the jointerRabbet Cutting To bevel cut on the jointerTo rabbet cut on the jointer H7765-8 Byrd Shelix Cutterhead G3631-Jointer Knife HoneDispoz-A-BladeHolder and Knife T20448T20452 T20501 T20456 H0736 Our most popular eye protectionDaily Check ScheduleLubrication Monthly CheckCleaning To adjust/replace the V-beltBelts Troubleshooting Motor & ElectricalCutting To inspect the knives Setting/Replacing KnivesInspecting Knives To set or replace the knivesPage Positive Stop Bolts Setting Infeed TableCalibrating Depth Scale Depth Stop LeverSetting Fence Stops To set the 45˚ inward fence stopTo set the 90˚ fence stop Adjusting Gibs To adjust the table gibsTo set the 45˚ outward fence stop Wiring Diagram See FigureTable Parts Breakdown GIB Bolt Fence Parts Breakdown Fence Parts List Stand Parts Breakdown Description PAINT1 Grizzly Green TOUCH-UP Paint Page Page Warranty and Returns