Grizzly G0656X manual Edge Jointing, To surface plane on the jointer

Page 39

To surface plane on the jointer:

1.Read and understand SECTION 1: SAFETY, beginning on Page 6.

2.Make sure your stock has been inspected for dangerous conditions as described in the Stock Inspection & Requirements instruc- tions, beginning on Page 21.

3.Set the cutting depth for your operation. (We suggest 1⁄32" for surface planing, using a more shallow depth for hard wood species or for wide stock.)

4.Make sure your fence is set to 90˚.

5.If your workpiece is cupped (warped), place it so the concave side is face down on the surface of the infeed table.

6.Start the jointer.

Failure to use push blocks when surface planing may result in cutterhead contact, which will cause serious personal injury. Always use push blocks to protect your hands when surface planing on the jointer.

7.With a push block in each hand, press the workpiece against the table and fence with firm pressure, and feed the workpiece over the cutterhead.

Note: If your leading hand (with push block) gets within 4" of the cutterhead, lift it up and over the cutterhead, and place the push block on the portion of the workpiece that is on the outfeed table. Now, focus your pres- sure on the outfeed end of the workpiece while feeding, and repeat the same action with your trailing hand when it gets within 4" of the cutterhead. To keep your hands safe, DO NOT let them get closer than 4" from the cutterhead when it is moving!

8.Repeat Step 7 until the entire surface is flat.

G0656 8" Jointer with Built-In Mobile Base

Edge Jointing

The purpose of edge jointing is to produce a fin- ished, flat-edged surface (see Figures 28 & 29) that is suitable for joinery or finishing. It is also a necessary step when squaring rough or warped stock.

NOTICE

If you are not experienced with a jointer, set the depth of cut to 0", and practice feeding the workpiece across the tables as described below. This procedure will better prepare you for the actual operation.

Figure 28. Typical edge jointing operation.

Figure 29. Illustration of edge jointing results.

-23-

Image 39

Contents Machine Inventory Setting Outfeed Table Height Wood Crate QtyTo set the outfeed table height Tools Needed Qty Replacing Carbide InsertsTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Table Parts Breakdown Description Table Parts ListFence Parts Breakdown Fence Parts List Stand Parts Breakdown Stand Parts List Label Placement Machine Inventory See Assembly Fasteners QtyClean Up See Assembly See Follow Steps 1-14 on Pages 14Perform Steps 18-26 on Pages 15 Handwheels installedModel G0656 Page Table of Contents Contact Info ForewordMachine Data Sheet G0656 8 Jointer with Built-In Mobile Base Identification Safety Instructions for Machinery G0656 8 Jointer with Built-In Mobile Base Additional Safety Instructions for Jointers Minimum Circuit Requirements Power Connection Device220V Operation Full Load Amperage DrawDescription Qty Setup SafetyItems Needed for Setup UnpackingCardboard Box Figure Qty InventoryHardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsTo assemble the jointer AssemblyChecking belt alignment Cutterhead Pulley Motor Page To connect a dust collection hose Dust Collection Setting OutfeedTighten V-Belt Recommended AdjustmentsFactory adjustments that should be verified Test RunOperations Operation Safety Jointer OverviewStart Button Starts motor Basic ControlsScrape all glue off of boards before joint- ing Stock Inspection RequirementsSurface Planing Squaring StockTo surface plane on the jointer Edge JointingTo edge joint on the jointer Bevel CuttingTo bevel cut on the jointer Rabbet CuttingTo rabbet cut on the jointer G3631-Jointer Knife Hone H7765-8 Byrd Shelix CutterheadDispoz-A-BladeHolder and Knife Our most popular eye protection T20448T20452 T20501 T20456 H0736Monthly Check ScheduleLubrication Daily CheckCleaning To adjust/replace the V-beltBelts Motor & Electrical TroubleshootingCutting To set or replace the knives Setting/Replacing KnivesInspecting Knives To inspect the knivesPage Depth Stop Lever Setting Infeed TableCalibrating Depth Scale Positive Stop BoltsSetting Fence Stops To set the 45˚ inward fence stopTo set the 90˚ fence stop Adjusting Gibs To adjust the table gibsTo set the 45˚ outward fence stop See Figure Wiring DiagramTable Parts Breakdown GIB Bolt Fence Parts Breakdown Fence Parts List Stand Parts Breakdown Description PAINT1 Grizzly Green TOUCH-UP Paint Page Page Warranty and Returns