Grizzly G0656X manual Setup Safety, Items Needed for Setup, Unpacking, Description Qty

Page 26

SECTION 3: SETUP

Setup Safety

This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine!

Wear safety glasses dur- ing the entire setup pro- cess!

This machine and its com- ponents are very heavy. Get lifting help or use power lifting equipment such as a forklift to move heavy items.

-10-

Items Needed for

Setup

The following items are needed to complete the setup process, but are not included with your machine:

Description		Qty
• Safety Glasses (for each person)		.............. 1
• Wrench or Socket 17mm		2
• Wrench or Socket 13mm		2
• Extra Person for Lifting Help		1
• Straightedge (see Page 28)		1
•	Phillips Head Screwdriver	1
•	Dust Collection System	1
• 4" Dust Hose (length as needed)		1
•	4" Hose Clamp	1

Unpacking

Your machine was carefully packaged for safe transportation. Remove the packaging materials from around your machine and inspect it. If you discover the machine is damaged, please imme- diately call Customer Service at (570) 546-9663 for advice.

Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi- tion of your shipment, inventory the contents.

G0656 8" Jointer with Built-In Mobile Base

Image 26

Contents To set the outfeed table height Machine Inventory Setting Outfeed Table HeightWood Crate Qty Replacing Carbide Inserts Tools Needed QtyTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Table Parts Breakdown Table Parts List DescriptionFence Parts Breakdown Fence Parts List Stand Parts Breakdown Stand Parts List Label Placement Assembly See Follow Steps 1-14 on Pages 14 Assembly Fasteners QtyClean Up See Machine Inventory SeeHandwheels installed Perform Steps 18-26 on Pages 15Model G0656 Page Table of Contents Foreword Contact InfoMachine Data Sheet G0656 8 Jointer with Built-In Mobile Base Identification Safety Instructions for Machinery G0656 8 Jointer with Built-In Mobile Base Additional Safety Instructions for Jointers Full Load Amperage Draw Power Connection Device220V Operation Minimum Circuit RequirementsUnpacking Setup SafetyItems Needed for Setup Description QtyInventory Cardboard Box Figure QtyHardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadAssembly To assemble the jointerChecking belt alignment Cutterhead Pulley Motor Page Dust Collection Setting Outfeed To connect a dust collection hoseTest Run Recommended AdjustmentsFactory adjustments that should be verified Tighten V-BeltOperation Safety Jointer Overview OperationsBasic Controls Start Button Starts motorStock Inspection Requirements Scrape all glue off of boards before joint- ingSquaring Stock Surface PlaningEdge Jointing To surface plane on the jointerBevel Cutting To edge joint on the jointerRabbet Cutting To bevel cut on the jointerTo rabbet cut on the jointer H7765-8 Byrd Shelix Cutterhead G3631-Jointer Knife HoneDispoz-A-BladeHolder and Knife T20448T20452 T20501 T20456 H0736 Our most popular eye protectionDaily Check ScheduleLubrication Monthly CheckBelts CleaningTo adjust/replace the V-belt Troubleshooting Motor & ElectricalCutting To inspect the knives Setting/Replacing KnivesInspecting Knives To set or replace the knivesPage Positive Stop Bolts Setting Infeed TableCalibrating Depth Scale Depth Stop LeverTo set the 90˚ fence stop Setting Fence StopsTo set the 45˚ inward fence stop To set the 45˚ outward fence stop Adjusting GibsTo adjust the table gibs Wiring Diagram See FigureTable Parts Breakdown GIB Bolt Fence Parts Breakdown Fence Parts List Stand Parts Breakdown Description PAINT1 Grizzly Green TOUCH-UP Paint Page Page Warranty and Returns