Grizzly G0656X manual Dispoz-A-BladeHolder and Knife

Page 44

G5562—SLIPIT®1 Qt. Gel G5563—SLIPIT®12 oz Spray G2871—Boeshield®T-9 12 oz Spray G2870—Boeshield®T-9 4 oz Spray H3788—G96®Gun Treatment 12 oz Spray H3789—G96®Gun Treatment 4.5 oz Spray

Figure 38. Recommended products for protect- ing unpainted cast iron/steel part on machinery.

H5142—Dispoz-A-Blade®System (Includes 4 Holders & Knife Inserts) H5143—Dispoz-A-Blade®Knife Inserts (Set of 4)

Install a Dispoz-A-Blade®Knife system in your new jointer and save up to 70% on knife replace- ments for the life of your jointer. Each knife insert is double-edged, so you get two knives in one, and is indexed so that all knife inserts can be installed at the same height in just minutes. Very simple and super fast knife changes!

Figure 39. Dispoz-A-Blade®Holder and Knife.

-28-

H4982—8" HSS Replacement Jointer Knives (Set of 4)

H8029—5 Piece Safety Kit

This kit has four essential jigs. Includes two push blocks, push stick, featherboard and com- bination saw and router gauge. Featherboard fits 3⁄8" x 3⁄4" miter slots. Made of high visibility yellow plastic.

Figure 40. H8029 5 Piece Safety Kit.

G9643—8" Precision Straightedge

G9644—12" Precision Straightedge

H2675—16" Precision Straightedge

These grade 00 heavy-duty stainless steel straightedges are manufactured to DIN874 stan- dards for professional results in set-up and inspection work.

Figure 41. Straightedges.

G0656 8" Jointer with Built-In Mobile Base

Image 44

Contents To set the outfeed table height Machine Inventory Setting Outfeed Table HeightWood Crate Qty Replacing Carbide Inserts Tools Needed QtyTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Table Parts Breakdown Table Parts List DescriptionFence Parts Breakdown Fence Parts List Stand Parts Breakdown Stand Parts List Label Placement Assembly Fasteners Qty Clean Up SeeAssembly See Follow Steps 1-14 on Pages 14 Machine Inventory SeeHandwheels installed Perform Steps 18-26 on Pages 15Model G0656 Page Table of Contents Foreword Contact InfoMachine Data Sheet G0656 8 Jointer with Built-In Mobile Base Identification Safety Instructions for Machinery G0656 8 Jointer with Built-In Mobile Base Additional Safety Instructions for Jointers Power Connection Device 220V OperationFull Load Amperage Draw Minimum Circuit RequirementsSetup Safety Items Needed for SetupUnpacking Description QtyInventory Cardboard Box Figure QtyHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadAssembly To assemble the jointerChecking belt alignment Cutterhead Pulley Motor Page Dust Collection Setting Outfeed To connect a dust collection hoseRecommended Adjustments Factory adjustments that should be verifiedTest Run Tighten V-BeltOperation Safety Jointer Overview OperationsBasic Controls Start Button Starts motorStock Inspection Requirements Scrape all glue off of boards before joint- ingSquaring Stock Surface PlaningEdge Jointing To surface plane on the jointerBevel Cutting To edge joint on the jointerRabbet Cutting To bevel cut on the jointerTo rabbet cut on the jointer H7765-8 Byrd Shelix Cutterhead G3631-Jointer Knife HoneDispoz-A-BladeHolder and Knife T20448T20452 T20501 T20456 H0736 Our most popular eye protectionSchedule LubricationDaily Check Monthly CheckBelts CleaningTo adjust/replace the V-belt Troubleshooting Motor & ElectricalCutting Setting/Replacing Knives Inspecting KnivesTo inspect the knives To set or replace the knivesPage Setting Infeed Table Calibrating Depth ScalePositive Stop Bolts Depth Stop LeverTo set the 90˚ fence stop Setting Fence StopsTo set the 45˚ inward fence stop To set the 45˚ outward fence stop Adjusting GibsTo adjust the table gibs Wiring Diagram See FigureTable Parts Breakdown GIB Bolt Fence Parts Breakdown Fence Parts List Stand Parts Breakdown Description PAINT1 Grizzly Green TOUCH-UP Paint Page Page Warranty and Returns