Grizzly G0656X manual Table of Contents

Page 17

Table of Contents

INTRODUCTION	2
Foreword	2
Contact Info	2
Machine Data Sheet	3
Identification	5
SECTION 1: SAFETY	6
Safety Instructions for Machinery	6
Additional Safety Instructions for Jointers	8
SECTION 2: CIRCUIT REQUIREMENTS	9
220V Operation	9
SECTION 3: SETUP	10
Setup Safety	10
Items Needed for Setup	10
Unpacking	10
Inventory	11
Hardware Recognition Chart	12
Clean Up	13
Site Considerations	13
Assembly	14
Dust Collection	17
Setting Outfeed Table Height	17
Test Run	18
Recommended Adjustments	18
Tighten V-Belt	18
SECTION 4: OPERATIONS	19
Operation Safety	19
Jointer Overview	19

Basic Controls	20
Stock Inspection & Requirements	21
Squaring Stock	22
Surface Planing	22
Edge Jointing	23
Bevel Cutting	24
Rabbet Cutting	25
SECTION 5: ACCESSORIES	27
SECTION 6: MAINTENANCE	30
Schedule	30
Lubrication	30
Cleaning	31
V-Belts	31
SECTION 7: SERVICE	32
Troubleshooting	32
Inspecting Knives	34
Setting/Replacing Knives	34
Setting Infeed Table	36
Setting Fence Stops	37
Adjusting Gibs	38
Wiring Diagram	39
Table Parts Breakdown	40
Fence Parts Breakdown	42
Stand Parts Breakdown	44
Label Placement	46
WARRANTY AND RETURNS	49

Image 17

Contents To set the outfeed table height Machine Inventory Setting Outfeed Table HeightWood Crate Qty Tools Needed Qty Replacing Carbide InsertsTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Table Parts Breakdown Description Table Parts ListFence Parts Breakdown Fence Parts List Stand Parts Breakdown Stand Parts List Label Placement Clean Up See Assembly Fasteners QtyAssembly See Follow Steps 1-14 on Pages 14 Machine Inventory SeePerform Steps 18-26 on Pages 15 Handwheels installedModel G0656 Page Table of Contents Contact Info ForewordMachine Data Sheet G0656 8 Jointer with Built-In Mobile Base Identification Safety Instructions for Machinery G0656 8 Jointer with Built-In Mobile Base Additional Safety Instructions for Jointers 220V Operation Power Connection DeviceFull Load Amperage Draw Minimum Circuit RequirementsItems Needed for Setup Setup SafetyUnpacking Description QtyCardboard Box Figure Qty InventoryHardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadTo assemble the jointer AssemblyChecking belt alignment Cutterhead Pulley Motor Page To connect a dust collection hose Dust Collection Setting OutfeedFactory adjustments that should be verified Recommended AdjustmentsTest Run Tighten V-BeltOperations Operation Safety Jointer OverviewStart Button Starts motor Basic ControlsScrape all glue off of boards before joint- ing Stock Inspection RequirementsSurface Planing Squaring StockTo surface plane on the jointer Edge JointingTo edge joint on the jointer Bevel CuttingTo bevel cut on the jointer Rabbet CuttingTo rabbet cut on the jointer G3631-Jointer Knife Hone H7765-8 Byrd Shelix CutterheadDispoz-A-BladeHolder and Knife Our most popular eye protection T20448T20452 T20501 T20456 H0736Lubrication ScheduleDaily Check Monthly CheckBelts CleaningTo adjust/replace the V-belt Motor & Electrical TroubleshootingCutting Inspecting Knives Setting/Replacing KnivesTo inspect the knives To set or replace the knivesPage Calibrating Depth Scale Setting Infeed TablePositive Stop Bolts Depth Stop LeverTo set the 90˚ fence stop Setting Fence StopsTo set the 45˚ inward fence stop To set the 45˚ outward fence stop Adjusting GibsTo adjust the table gibs See Figure Wiring DiagramTable Parts Breakdown GIB Bolt Fence Parts Breakdown Fence Parts List Stand Parts Breakdown Description PAINT1 Grizzly Green TOUCH-UP Paint Page Page Warranty and Returns