Grizzly G0656X manual

Page 32

19. Using a 2.5mm hex wrench, thread the set screw through the hole in the forked end of the cutterhead guard shaft (Figure 14).

Note: Thread the set screw far enough to prevent the guard from being pulled out.

Figure 14. Example of installing cutterhead

guard set screw.

20.Raise the fence and rotate the guard one revolution counter-clockwise as it appears from the top. Hold the guard in position.

21.Lower the fence and allow the guard to swing back against the fence.

NOTICE

The cutterhead guard must always return to the closed position whenever it is moved.

22.Test the guard by pulling it back and letting it go.

—The guard should snap back over the cutterhead without dragging across the table.

—If the guard drags across the table, loosen the set screw, raise the guard until it won't drag, then tighten the set screw.

—If the guard does not snap back, remove it and repeat Steps 18–21.

23.Attach the pedestal switch with the cap screws, lock washers, and flat washers, as shown in Figure 15.

Figure 15. Attaching pedestal switch to stand.

24.Thread the excess switch cord through the access hole in the stand and connect it to the motor cord.

25.Assemble the knife setting gauge using the knife setting gauge rod, feet and 8mm e- clips, as shown in Figure 16.

Figure 16. Knife setting gauge assembly.

26.Replace the rear access panel on the stand.

-16-	G0656 8" Jointer with Built-In Mobile Base

Image 32

Contents To set the outfeed table height Machine Inventory Setting Outfeed Table HeightWood Crate Qty Replacing Carbide Inserts Tools Needed QtyTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Table Parts Breakdown Table Parts List DescriptionFence Parts Breakdown Fence Parts List Stand Parts Breakdown Stand Parts List Label Placement Assembly Fasteners Qty Clean Up SeeAssembly See Follow Steps 1-14 on Pages 14 Machine Inventory SeeHandwheels installed Perform Steps 18-26 on Pages 15Model G0656 Page Table of Contents Foreword Contact InfoMachine Data Sheet G0656 8 Jointer with Built-In Mobile Base Identification Safety Instructions for Machinery G0656 8 Jointer with Built-In Mobile Base Additional Safety Instructions for Jointers Power Connection Device 220V OperationFull Load Amperage Draw Minimum Circuit RequirementsSetup Safety Items Needed for SetupUnpacking Description QtyInventory Cardboard Box Figure QtyHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadAssembly To assemble the jointerChecking belt alignment Cutterhead Pulley Motor Page Dust Collection Setting Outfeed To connect a dust collection hoseRecommended Adjustments Factory adjustments that should be verifiedTest Run Tighten V-BeltOperation Safety Jointer Overview OperationsBasic Controls Start Button Starts motorStock Inspection Requirements Scrape all glue off of boards before joint- ingSquaring Stock Surface PlaningEdge Jointing To surface plane on the jointerBevel Cutting To edge joint on the jointerRabbet Cutting To bevel cut on the jointerTo rabbet cut on the jointer H7765-8 Byrd Shelix Cutterhead G3631-Jointer Knife HoneDispoz-A-BladeHolder and Knife T20448T20452 T20501 T20456 H0736 Our most popular eye protectionSchedule LubricationDaily Check Monthly CheckBelts CleaningTo adjust/replace the V-belt Troubleshooting Motor & ElectricalCutting Setting/Replacing Knives Inspecting KnivesTo inspect the knives To set or replace the knivesPage Setting Infeed Table Calibrating Depth ScalePositive Stop Bolts Depth Stop LeverTo set the 90˚ fence stop Setting Fence StopsTo set the 45˚ inward fence stop To set the 45˚ outward fence stop Adjusting GibsTo adjust the table gibs Wiring Diagram See FigureTable Parts Breakdown GIB Bolt Fence Parts Breakdown Fence Parts List Stand Parts Breakdown Description PAINT1 Grizzly Green TOUCH-UP Paint Page Page Warranty and Returns