Grizzly G0656X manual Clean Up, Site Considerations, Floor Load, Placement Location

Page 29

Clean Up

The unpainted surfaces are coated with a waxy oil to prevent corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Citrus Degreaser. To clean thoroughly, some parts must be removed. For optimum performance from your machine, clean all moving parts or sliding contact surfaces. Avoid chlorine-based solvents, such as acetone or brake parts cleaner that may damage painted surfaces. Always follow the manufacturer’s instructions when using any type of cleaning product.

To access the sliding surfaces, remove the lock nut (Figure 5) and flat washer securing the fence lock handle, and remove the fence from the jointer unit.

Fence Lock

Handle

Fence Lock Nut

Figure 5. Removing the fence lock nut so the

sliding surfaces can be cleaned.

Once the sliding surfaces of the fence are clean, reassemble the fence to the jointer and secure the lock handle with the lock nut and washer.

Gasoline and petroleum products have low flash points and can explode or cause fire if used to clean machinery. DO NOT use these products to clean the machinery.

Site Considerations

Floor Load

Refer to the Machine Data Sheet for the weight and footprint specifications of your machine. Some residential floors may require additional reinforcement to support both the machine and operator.

Placement Location

Consider existing and anticipated needs, size of material to be processed through each machine, and space for auxiliary stands, work tables or other machinery when establishing a location for your new machine. See Figure 6 for the minimum working clearances.

��

����

���

Figure 6. Minimum working clearances.

Children and visitors may be seriously injured if unsuper- vised around this machine. Lock entrances to the shop or disable start switch or power connection to prevent unsupervised use.

G0656 8" Jointer with Built-In Mobile Base

-13-

Image 29
Contents To set the outfeed table height Machine Inventory Setting Outfeed Table HeightWood Crate Qty Tools Needed Qty Replacing Carbide InsertsTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Table Parts Breakdown Description Table Parts ListFence Parts Breakdown Fence Parts List Stand Parts Breakdown Stand Parts List Label Placement Clean Up See Assembly Fasteners QtyAssembly See Follow Steps 1-14 on Pages 14 Machine Inventory SeePerform Steps 18-26 on Pages 15 Handwheels installedModel G0656 Page Table of Contents Contact Info ForewordMachine Data Sheet G0656 8 Jointer with Built-In Mobile Base Identification Safety Instructions for Machinery G0656 8 Jointer with Built-In Mobile Base Additional Safety Instructions for Jointers 220V Operation Power Connection DeviceFull Load Amperage Draw Minimum Circuit RequirementsItems Needed for Setup Setup SafetyUnpacking Description QtyCardboard Box Figure Qty InventoryHardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadTo assemble the jointer AssemblyChecking belt alignment Cutterhead Pulley Motor Page To connect a dust collection hose Dust Collection Setting OutfeedFactory adjustments that should be verified Recommended AdjustmentsTest Run Tighten V-BeltOperations Operation Safety Jointer OverviewStart Button Starts motor Basic ControlsScrape all glue off of boards before joint- ing Stock Inspection RequirementsSurface Planing Squaring StockTo surface plane on the jointer Edge JointingTo edge joint on the jointer Bevel CuttingTo bevel cut on the jointer Rabbet CuttingTo rabbet cut on the jointer G3631-Jointer Knife Hone H7765-8 Byrd Shelix CutterheadDispoz-A-BladeHolder and Knife Our most popular eye protection T20448T20452 T20501 T20456 H0736Lubrication ScheduleDaily Check Monthly CheckBelts CleaningTo adjust/replace the V-belt Motor & Electrical TroubleshootingCutting Inspecting Knives Setting/Replacing KnivesTo inspect the knives To set or replace the knivesPage Calibrating Depth Scale Setting Infeed TablePositive Stop Bolts Depth Stop LeverTo set the 90˚ fence stop Setting Fence StopsTo set the 45˚ inward fence stop To set the 45˚ outward fence stop Adjusting GibsTo adjust the table gibs See Figure Wiring DiagramTable Parts Breakdown GIB Bolt Fence Parts Breakdown Fence Parts List Stand Parts Breakdown Description PAINT1 Grizzly Green TOUCH-UP Paint Page Page Warranty and Returns