Grizzly G0656X manual Squaring Stock, Surface Planing

Page 38

Squaring Stock

Squaring stock involves four steps performed in the order below:

1.Surface Plane On The Jointer—The con- cave face of the workpiece is surface planed flat with the jointer.

2.Surface Plane On a Thickness Planer—The opposite face of the workpiece is surface planed flat with a thickness planer.

Previously

Surface

Planed Face

3.Edge Joint On The Jointer—The concave edge of the workpiece is jointed flat with the jointer.

4.Rip Cut On A Table Saw—The jointed edge of the workpiece is placed against a table saw

fence and the opposite edge cut off.

Previously

Jointed Edge

��

��

��

Surface Planing

The purpose of surface planing on the jointer is to make one flat face on a piece of stock (see Figures 26 & 27). This is a necessary step when preparing a workpiece to be run through a planer when squaring stock.

NOTICE If you are not experienced with a jointer, set the depth of cut to 0", and practice feeding the workpiece across the tables as described. This procedure will better pre- pare you for the actual operation.

Figure 26. Typical surface planing operation.

Figure 27. Illustration of surface planing results.

-22-	G0656 8" Jointer with Built-In Mobile Base

Image 38

Contents To set the outfeed table height Machine Inventory Setting Outfeed Table HeightWood Crate Qty Replacing Carbide Inserts Tools Needed QtyTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Table Parts Breakdown Table Parts List DescriptionFence Parts Breakdown Fence Parts List Stand Parts Breakdown Stand Parts List Label Placement Assembly See Follow Steps 1-14 on Pages 14 Assembly Fasteners QtyClean Up See Machine Inventory SeeHandwheels installed Perform Steps 18-26 on Pages 15Model G0656 Page Table of Contents Foreword Contact InfoMachine Data Sheet G0656 8 Jointer with Built-In Mobile Base Identification Safety Instructions for Machinery G0656 8 Jointer with Built-In Mobile Base Additional Safety Instructions for Jointers Full Load Amperage Draw Power Connection Device220V Operation Minimum Circuit RequirementsUnpacking Setup SafetyItems Needed for Setup Description QtyInventory Cardboard Box Figure QtyHardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadAssembly To assemble the jointerChecking belt alignment Cutterhead Pulley Motor Page Dust Collection Setting Outfeed To connect a dust collection hoseTest Run Recommended AdjustmentsFactory adjustments that should be verified Tighten V-BeltOperation Safety Jointer Overview OperationsBasic Controls Start Button Starts motorStock Inspection Requirements Scrape all glue off of boards before joint- ingSquaring Stock Surface PlaningEdge Jointing To surface plane on the jointerBevel Cutting To edge joint on the jointerRabbet Cutting To bevel cut on the jointerTo rabbet cut on the jointer H7765-8 Byrd Shelix Cutterhead G3631-Jointer Knife HoneDispoz-A-BladeHolder and Knife T20448T20452 T20501 T20456 H0736 Our most popular eye protectionDaily Check ScheduleLubrication Monthly CheckBelts CleaningTo adjust/replace the V-belt Troubleshooting Motor & ElectricalCutting To inspect the knives Setting/Replacing KnivesInspecting Knives To set or replace the knivesPage Positive Stop Bolts Setting Infeed TableCalibrating Depth Scale Depth Stop LeverTo set the 90˚ fence stop Setting Fence StopsTo set the 45˚ inward fence stop To set the 45˚ outward fence stop Adjusting GibsTo adjust the table gibs Wiring Diagram See FigureTable Parts Breakdown GIB Bolt Fence Parts Breakdown Fence Parts List Stand Parts Breakdown Description PAINT1 Grizzly Green TOUCH-UP Paint Page Page Warranty and Returns