Grizzly G0656X manual Checking belt alignment Cutterhead Pulley Motor

Page 31

9.Slide the motor upward, and place the V-belt around the cutterhead pulley and the motor pulley.

10.Slide the motor down to rest on the V-belt.

11.Place a straightedge against both pulleys (Figure 10) and check the alignment of the two pulleys to make sure that they are aligned and that the V-belt is straight up and down (see Figure 11).

Straightedge

Figure 10. Checking belt alignment.

Cutterhead

Pulley

���������

Motor

Pulley

Figure 11. Pulleys aligned.

If the pulleys are aligned, tighten the motor bracket fasteners and go to Step 15.

If the pulleys are NOT aligned, perform Steps 12–14.

12.Remove the V-belt and loosen the motor mount fasteners (see Figure 9).

13.Shift the motor horizontally as needed to align the motor pulley with the cutterhead pul- ley, then replace the V-belt.

14.Tighten the motor mount fasteners.

15.Secure the infeed and outfeed handwheels with the cap screws and flat washers already mounted on the handwheel shafts, as shown in Figure 12.

Figure 12. Securing the handwheel handle.

16.Secure the handwheel handles to each of the the handwheels, as shown in Figure 12.

17. Install the fence tilt lever, as shown in Figure 13.

Figure 13. Fence tilt lever installed.

18. Slide the cutterhead guard shaft down through the mounting hole on the table.

Note: The guard may not fully seat in the hole initially; however, rotating the guard will allow the shaft to fully seat in the hole.

G0656 8" Jointer with Built-In Mobile Base

-15-

Image 31
Contents Wood Crate Qty Machine Inventory Setting Outfeed Table HeightTo set the outfeed table height Tools Needed Qty Replacing Carbide InsertsTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Table Parts Breakdown Description Table Parts ListFence Parts Breakdown Fence Parts List Stand Parts Breakdown Stand Parts List Label Placement Machine Inventory See Assembly Fasteners QtyClean Up See Assembly See Follow Steps 1-14 on Pages 14Perform Steps 18-26 on Pages 15 Handwheels installedModel G0656 Page Table of Contents Contact Info ForewordMachine Data Sheet G0656 8 Jointer with Built-In Mobile Base Identification Safety Instructions for Machinery G0656 8 Jointer with Built-In Mobile Base Additional Safety Instructions for Jointers Minimum Circuit Requirements Power Connection Device220V Operation Full Load Amperage DrawDescription Qty Setup SafetyItems Needed for Setup UnpackingCardboard Box Figure Qty InventoryHardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsTo assemble the jointer AssemblyChecking belt alignment Cutterhead Pulley Motor Page To connect a dust collection hose Dust Collection Setting OutfeedTighten V-Belt Recommended AdjustmentsFactory adjustments that should be verified Test RunOperations Operation Safety Jointer OverviewStart Button Starts motor Basic ControlsScrape all glue off of boards before joint- ing Stock Inspection RequirementsSurface Planing Squaring StockTo surface plane on the jointer Edge JointingTo edge joint on the jointer Bevel CuttingTo bevel cut on the jointer Rabbet CuttingTo rabbet cut on the jointer G3631-Jointer Knife Hone H7765-8 Byrd Shelix CutterheadDispoz-A-BladeHolder and Knife Our most popular eye protection T20448T20452 T20501 T20456 H0736Monthly Check ScheduleLubrication Daily CheckTo adjust/replace the V-belt CleaningBelts Motor & Electrical TroubleshootingCutting To set or replace the knives Setting/Replacing KnivesInspecting Knives To inspect the knivesPage Depth Stop Lever Setting Infeed TableCalibrating Depth Scale Positive Stop BoltsTo set the 45˚ inward fence stop Setting Fence StopsTo set the 90˚ fence stop To adjust the table gibs Adjusting GibsTo set the 45˚ outward fence stop See Figure Wiring DiagramTable Parts Breakdown GIB Bolt Fence Parts Breakdown Fence Parts List Stand Parts Breakdown Description PAINT1 Grizzly Green TOUCH-UP Paint Page Page Warranty and Returns