Grizzly G0656X manual Inventory, Cardboard Box Figure Qty

Page 27

Inventory

The following is a description of the main compo- nents shipped with your machine. Lay the compo- nents out to inventory them.

Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully. Occasionally we pre-install certain components for shipping purposes.

H

G

F

E

A

B

C

D

Wood Crate: (Figure 3)

Qty

A.

Jointer Assembly

1

B.

Cutterhead Guard

1

C.

Handwheels

2

D.

Handles

2

E.

Fence Tilt Lever

1

F.

Push Blocks

2

G.Knife Setting Gauge Hardware Bag

 

—Knife Setting Gauge Rod

1

 

—Knife Setting Gauge Foot

2

 

—E-Clip 8mm

2

H.

Tool Hardware Bag

 

 

 

—Hex Wrenches 2.5, 3, 4, 6mm

1 Each

 

—Open-end Wrench 8/10, 12/14mm

1

Cardboard Box: (Figure 4)

 

Qty

I.

Stand Assembly w/Motor and Door

1

J.

Pedestal Switch

1

K.

Wheel Assembly

1

L.

V-Belt

1

M.

Dust Port

1

Assembly Fasteners

 

Qty

•

Hex Bolt M8-1.25 x 50 (Wheel/Stand)

1

•

Flat Washer 8mm (Wheel/Stand)

1

•

Hex Bolts M10-1.5 x 55 (Wheel/Stand)

2

•

Flat Washers 10mm (Wheel/Stand)

2

•

Hex Nuts M10-1.5 (Wheel/Stand)

2

•Cap Screws M8-1.25 x 50 (Jointer/Stand) . 3

• Flat Washers 8mm (Jointer/Stand)

6

• Lock Washers 8mm (Jointer/Stand)

3

• Hex Nuts M8-1.25 (Jointer/Stand)

3

•

Flat Washers 6mm (Handwheels)

2

•

Cap Screws M6-1 x 12 (Handwheels)

2

•Set Screw M5-.8 x 12 (Cutterhead Guard) 1

• Cap Screws M8-1.25 x 25 (Pedestal)

2

•

Lock Washers (Pedestal)

2

•

Flat Washers (Pedestal)

2

•

Phillips Head Screws

 

 

M5-.8 x 16 (Dust Port)

4

• Flat Washers 5mm (Dust Port)

4

G0656 8" Jointer with Built-In Mobile Base

 

Figure 3. Box 1 inventory contents.

I

M

J

LK

Figure 4. Box 2 inventory contents.

•Cap Screws M8-1.25 x 25 (Fence Suppt.). 4

•Flat Wshers 8mm (Fence Support)............ 4

•Lock Washers 8mm (Fence Supptort) ....... 4

In the event that any nonproprietary parts are missing (e.g. a nut or a washer), we would be glad to replace them, or for the sake of expedi- ency, replacements can be obtained at your local hardware store.

SUFFOCATION HAZARD!

Immediately discard all plas- tic bags and packing materi- als to eliminate choking/suf- focation hazards for children and animals.

-11-

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Machine Inventory Setting Outfeed Table Height Wood Crate QtyTo set the outfeed table height Tools Needed Qty Replacing Carbide InsertsTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Table Parts Breakdown Description Table Parts ListFence Parts Breakdown Fence Parts List Stand Parts Breakdown Stand Parts List Label Placement Machine Inventory See Assembly Fasteners QtyClean Up See Assembly See Follow Steps 1-14 on Pages 14Perform Steps 18-26 on Pages 15 Handwheels installedModel G0656 Page Table of Contents Contact Info ForewordMachine Data Sheet G0656 8 Jointer with Built-In Mobile Base Identification Safety Instructions for Machinery G0656 8 Jointer with Built-In Mobile Base Additional Safety Instructions for Jointers Minimum Circuit Requirements Power Connection Device220V Operation Full Load Amperage DrawDescription Qty Setup SafetyItems Needed for Setup UnpackingCardboard Box Figure Qty InventoryHardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsTo assemble the jointer AssemblyChecking belt alignment Cutterhead Pulley Motor Page To connect a dust collection hose Dust Collection Setting OutfeedTighten V-Belt Recommended AdjustmentsFactory adjustments that should be verified Test RunOperations Operation Safety Jointer OverviewStart Button Starts motor Basic ControlsScrape all glue off of boards before joint- ing Stock Inspection RequirementsSurface Planing Squaring StockTo surface plane on the jointer Edge JointingTo edge joint on the jointer Bevel CuttingTo bevel cut on the jointer Rabbet CuttingTo rabbet cut on the jointer G3631-Jointer Knife Hone H7765-8 Byrd Shelix CutterheadDispoz-A-BladeHolder and Knife Our most popular eye protection T20448T20452 T20501 T20456 H0736Monthly Check ScheduleLubrication Daily CheckCleaning To adjust/replace the V-beltBelts Motor & Electrical TroubleshootingCutting To set or replace the knives Setting/Replacing KnivesInspecting Knives To inspect the knivesPage Depth Stop Lever Setting Infeed TableCalibrating Depth Scale Positive Stop BoltsSetting Fence Stops To set the 45˚ inward fence stopTo set the 90˚ fence stop Adjusting Gibs To adjust the table gibsTo set the 45˚ outward fence stop See Figure Wiring DiagramTable Parts Breakdown GIB Bolt Fence Parts Breakdown Fence Parts List Stand Parts Breakdown Description PAINT1 Grizzly Green TOUCH-UP Paint Page Page Warranty and Returns
Top Page Image Contents