Grizzly G0656X manual Label Placement

Page 12

Label Placement

300

312

311

310

309

308

REF	PART #	DESCRIPTION

300	P0656300	FENCE/CUTTERHEAD LABEL
301	P0656301	CUTTTERHEAD GUARD LABEL
302	PLABEL-14	ELECTRICITY LABEL
303	PLABEL-11	SAFETY GLASSES 2" X 3 5/16"
304	PLABEL-15	EAR PROTECTION 2" X 3-5/16"H
305	PLABEL-63	UNPLUG 220V POWER LABEL
306	PLABEL-12A	READ MANUAL-VERTICAL NS 7/05

302

301

303

304

305

306

307

REF	PART #	DESCRIPTION

307	P0656X307	MODEL NUMBER LABEL
308	G8588	SMALL GRIZZLY NAMEPLATE
309	PPAINT-11	PUTTY TOUCH-UP PAINT
310	P0656X310	MACHINE ID LABEL
311	PPAINT-1	GRIZZLY GREEN TOUCH-UP PAINT
312	PPAINT-16	RED TOUCH-UP PAINT

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-12-	G0656X Manual Insert

Image 12

Contents Machine Inventory Setting Outfeed Table Height Wood Crate QtyTo set the outfeed table height Replacing Carbide Inserts Tools Needed QtyTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Table Parts Breakdown Table Parts List DescriptionFence Parts Breakdown Fence Parts List Stand Parts Breakdown Stand Parts List Label Placement Assembly Fasteners Qty Clean Up SeeAssembly See Follow Steps 1-14 on Pages 14 Machine Inventory SeeHandwheels installed Perform Steps 18-26 on Pages 15Model G0656 Page Table of Contents Foreword Contact InfoMachine Data Sheet G0656 8 Jointer with Built-In Mobile Base Identification Safety Instructions for Machinery G0656 8 Jointer with Built-In Mobile Base Additional Safety Instructions for Jointers Power Connection Device 220V OperationFull Load Amperage Draw Minimum Circuit RequirementsSetup Safety Items Needed for SetupUnpacking Description QtyInventory Cardboard Box Figure QtyHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadAssembly To assemble the jointerChecking belt alignment Cutterhead Pulley Motor Page Dust Collection Setting Outfeed To connect a dust collection hoseRecommended Adjustments Factory adjustments that should be verifiedTest Run Tighten V-BeltOperation Safety Jointer Overview OperationsBasic Controls Start Button Starts motorStock Inspection Requirements Scrape all glue off of boards before joint- ingSquaring Stock Surface PlaningEdge Jointing To surface plane on the jointerBevel Cutting To edge joint on the jointerRabbet Cutting To bevel cut on the jointerTo rabbet cut on the jointer H7765-8 Byrd Shelix Cutterhead G3631-Jointer Knife HoneDispoz-A-BladeHolder and Knife T20448T20452 T20501 T20456 H0736 Our most popular eye protectionSchedule LubricationDaily Check Monthly CheckCleaning To adjust/replace the V-beltBelts Troubleshooting Motor & ElectricalCutting Setting/Replacing Knives Inspecting KnivesTo inspect the knives To set or replace the knivesPage Setting Infeed Table Calibrating Depth ScalePositive Stop Bolts Depth Stop LeverSetting Fence Stops To set the 45˚ inward fence stopTo set the 90˚ fence stop Adjusting Gibs To adjust the table gibsTo set the 45˚ outward fence stop Wiring Diagram See FigureTable Parts Breakdown GIB Bolt Fence Parts Breakdown Fence Parts List Stand Parts Breakdown Description PAINT1 Grizzly Green TOUCH-UP Paint Page Page Warranty and Returns