Grizzly G0656X manual Assembly, To assemble the jointer

Page 30

Assembly

To assemble the jointer:

1.Carefully lay the stand on its side so you can access the underside.

2.Bolt the wheel assembly to the stand with the provided hardware, as shown in Figure 7.

Note: Refer to the Inventory List on Page 11 for a list of components needed for ass- sembly.

Hex Bolt M8-1.25 x 50

Flat Washer 8mm

Hex Bolts M10-1.5 x 55

Flat Washers 10mm

Hex Nuts

M10-1.5

Figure 7. Example of bolting the wheel assembly

to the stand.

3.Turn the stand rightside up.

The jointer is heavy. Seek assistance when lifting it onto the jointer stand.

4.Remove the rear access panel from the jointer stand.

-14-

5.With the help of an assistant, lift the jointer onto the stand.

6.Align the mounting holes on the jointer and stand.

7.Secure the jointer to the stand with the M8- 1.25 x 50 cap screws, washers, and hex nuts, as shown in Figure 8.

	��	��
	��	��
		��

��

��

��

��

Figure 8. Jointer secured to stand.

8.Using a 13mm wrench, loosen the motor bracket fasteners shown in Figure 9.

Note: DO NOT completely remove the motor mount bolts.

Figure 9. Motor bracket fasteners (black

arrows); motor mount fasteners (white arrows).

G0656 8" Jointer with Built-In Mobile Base

Image 30

Contents Machine Inventory Setting Outfeed Table Height Wood Crate QtyTo set the outfeed table height Replacing Carbide Inserts Tools Needed QtyTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Table Parts Breakdown Table Parts List DescriptionFence Parts Breakdown Fence Parts List Stand Parts Breakdown Stand Parts List Label Placement Assembly See Follow Steps 1-14 on Pages 14 Assembly Fasteners QtyClean Up See Machine Inventory SeeHandwheels installed Perform Steps 18-26 on Pages 15Model G0656 Page Table of Contents Foreword Contact InfoMachine Data Sheet G0656 8 Jointer with Built-In Mobile Base Identification Safety Instructions for Machinery G0656 8 Jointer with Built-In Mobile Base Additional Safety Instructions for Jointers Full Load Amperage Draw Power Connection Device220V Operation Minimum Circuit RequirementsUnpacking Setup SafetyItems Needed for Setup Description QtyInventory Cardboard Box Figure QtyHardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadAssembly To assemble the jointerChecking belt alignment Cutterhead Pulley Motor Page Dust Collection Setting Outfeed To connect a dust collection hoseTest Run Recommended AdjustmentsFactory adjustments that should be verified Tighten V-BeltOperation Safety Jointer Overview OperationsBasic Controls Start Button Starts motorStock Inspection Requirements Scrape all glue off of boards before joint- ingSquaring Stock Surface PlaningEdge Jointing To surface plane on the jointerBevel Cutting To edge joint on the jointerRabbet Cutting To bevel cut on the jointerTo rabbet cut on the jointer H7765-8 Byrd Shelix Cutterhead G3631-Jointer Knife HoneDispoz-A-BladeHolder and Knife T20448T20452 T20501 T20456 H0736 Our most popular eye protectionDaily Check ScheduleLubrication Monthly CheckCleaning To adjust/replace the V-beltBelts Troubleshooting Motor & ElectricalCutting To inspect the knives Setting/Replacing KnivesInspecting Knives To set or replace the knivesPage Positive Stop Bolts Setting Infeed TableCalibrating Depth Scale Depth Stop LeverSetting Fence Stops To set the 45˚ inward fence stopTo set the 90˚ fence stop Adjusting Gibs To adjust the table gibsTo set the 45˚ outward fence stop Wiring Diagram See FigureTable Parts Breakdown GIB Bolt Fence Parts Breakdown Fence Parts List Stand Parts Breakdown Description PAINT1 Grizzly Green TOUCH-UP Paint Page Page Warranty and Returns