Grizzly G0604 owner manual Circuit Requirements, 110V Operation

Page 11

SECTION 2: CIRCUIT REQUIREMENTS

110V Operation

Serious personal injury could occur if you connect the machine to the power source before you have completed the set up pro- cess. DO NOT connect the machine to the power source until instructed to do so.

Amperage Draw

The Model G0604 motor draws the following amps under maximum load:

Maximum Load

13 Amps

Circuit Requirements

We recommend connecting this machine to a dedicated circuit with a verified ground, using the circuit size given below. Never replace a circuit breaker with one of higher amperage without con- sulting a qualified electrician to ensure compli- ance with wiring codes. If you are unsure about the wiring codes in your area or you plan to connect your machine to a shared circuit, you may create a fire hazard—consult a qualified electrician to reduce this risk.

Recommended Circuit Size

15 Amps

Grounding

In the event of an electrical short, grounding reduces the risk of electric shock. This tool is equipped with a power cord that has a grounding wire, which must be properly connected to the grounding prong on the plug; likewise, the outlet must be properly installed and grounded. All elec- trical connections must be made in accordance with local codes and ordinances.

Electrocution or fire could result if this machine is not grounded correctly or if your electrical con- figuration does not com- ply with local and state codes. Ensure compliance by checking with a quali- fied electrician!

Extension Cords

We do not recommend the use of extension cords. Instead, arrange the placement of your equipment and the installed wiring to eliminate the need for extension cords.

If you must use an extension cord at 110V with your machine:

•

Plug/Receptacle Type

Included Plug/Receptacle ................ NEMA 5-15

•

•

Figure 1. NEMA 5-15 plug and receptacle.

G0604 6" X 56" Jointer

Use at least a 14 gauge cord that does not exceed 50 feet in length!

The extension cord must also contain a ground wire and plug pin.

Avoid cords over 50 feet long unless they have been sized by a qualified electrician.

-9-

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model G0604 Page Table of Contents Warranty and Returns Contact Info IntroductionForeword Machine Data Sheet Identification Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Jointers 110V Operation Circuit RequirementsUnpacking SetupSetup Safety Items Needed for SetupJointer Box Figure Qty Stand Assembly w/MotorAssembly Fasteners Qty InventoryHardware Recognition Chart Components and Hardware Needed Qty CleanupWheel Assembly Site ConsiderationsTo mount the jointer to the stand To install the V-beltJointerV-Belt To check the outfeed table height Checking Outfeed Table HeightExtension Table To install the extension tableSetting Outfeed Table Height on Fence To install the fenceCutterhead Guard Pedestal SwitchTo install the cutterhead guard To install the pedestal switchDust Port Knife Setting JigTest Run Recommended Factory adjustments that should be verifiedStart & Stop Buttons Figure Operation Safety Basic ControlsOperations Tilt lock and plunger locations Stock Inspection and RequirementsSquaring Stock Minimum dimensions for edge JointingTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingG3631-Jointer/Planer Knife Hone AccessoriesH9218-6 Byrd Shelix Cutterhead Dispoz-A-BladeHolder and Knife H1300 H1298 G7984 H2347 H0736 Our most popular safety glassesLubrication MaintenanceBelt Cleaning ScheduleTroubleshooting Guide ServiceCutting To inspect the knives Adjusting/Replacing KnivesInspecting Knives Tools Needed Qty To adjust/replace the knivesPage To check the outfeed table parallelism Checking/Adjusting Table ParallelismTo check the infeed table parallelism To adjust the table parallelismTo set the outfeed table height Setting Outfeed Table HeightPositive stop bolts for infeed table Setting Infeed TableTo calibrate the depth scale Setting Fence StopsCalibrating Depth ScaleTo set the 45 outward fence stop To set the 90˚ fence stopWiring Diagram Electrical Components Jointer Parts Breakdown Description Jointer Parts ListBumper Stand/Motor Parts Breakdown Stand/Motor Parts List PLABEL-29 Cutterhead Guard Label Warranty and Returns G0604 6 X 56 Jointer Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog
Top Page Image Contents