Grizzly G0604 owner manual Setting Outfeed Table Height, To set the outfeed table height

Page 40

Set Screw

EccentricLocation

Bushing

Figure 56. Eccentric bushing and set screw

location.

3.Place the straightedge in one of the positions shown in Figure 53, and adjust the table by turning the eccentric bearings (a small ham- mer and punch or pin-type spanner wrench may be necessary), so that the straightedge touches the cutterhead while lying flat across the outfeed table. Repeat this step with each of the remaining straightedge positions as necessary until the outfeed table is parallel with the cutterhead.

4.Tighten/replace the set screws in the eccen- tric bushings on the outfeed table.

5.Remove the set screw from each of the four eccentric bushings under the infeed table, and loosen the set screws underneath those removed set screws.

6.Place the straightedge halfway across the infeed table and halfway over the outfeed table, and adjust the infeed table even with the outfeed table, as shown in Figure 54.

7.Place the straightedge in one of the posi- tions shown in Figure 55, and adjust the eccentric bushings under the infeed table so the straightedge lies flat against both tables. Repeat this step with each of the remaining straightedge positions as many times as nec- essary until the infeed table is parallel with the outfeed table.

8.Tighten/replace the set screws in the eccen- tric bushings on the infeed table.

9.Set the knives (refer to Page 33), set the outfeed table height (refer to the next sub- section), and recalibrate the fence stops (Page 40).

10.Reinstall the cutterhead guard.

-38-

Setting Outfeed

Table Height

The outfeed table height must be even with the top of the cutterhead knives. If the outfeed table is set too low, there will be snipe. If the outfeed table is set too high, the workpiece will hit the edge of the outfeed table during operation, increasing the chance of kickback.

Tools Needed

Qty

Straightedge

1

Wrench 17mm

1

Hex Wrench 8mm

1

Hex Wrench 4mm

1

Hex Wrench 3mm

1

Feeler Gauge(s) 0.062"

1

To set the outfeed table height:

 

1.DISCONNECT JOINTER FROM POWER SOURCE!

2.Check/adjust the table parallelism.

3.Remove the cutterhead guard and fence.

4.Loosen the outfeed table lock located at the front of the machine, and loosen the jam nuts and positive stop bolts located at the back of the machine (see Figure 51).

G0604 6" X 56" Jointer

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Model G0604 Page Table of Contents Warranty and Returns Foreword IntroductionContact Info Machine Data Sheet Identification Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Jointers Circuit Requirements 110V OperationSetup Setup SafetyItems Needed for Setup UnpackingStand Assembly w/Motor Assembly Fasteners QtyInventory Jointer Box Figure QtyHardware Recognition Chart Cleanup Wheel AssemblySite Considerations Components and Hardware Needed QtyJointerV-Belt To install the V-beltTo mount the jointer to the stand Checking Outfeed Table Height To check the outfeed table heightSetting Outfeed Table Height on To install the extension tableExtension Table To install the fence FencePedestal Switch To install the cutterhead guardTo install the pedestal switch Cutterhead GuardKnife Setting Jig Dust PortFactory adjustments that should be verified Test Run RecommendedOperations Operation Safety Basic ControlsStart & Stop Buttons Figure Stock Inspection and Requirements Tilt lock and plunger locationsMinimum dimensions for edge Jointing Squaring StockSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerH9218-6 Byrd Shelix Cutterhead AccessoriesG3631-Jointer/Planer Knife Hone Dispoz-A-BladeHolder and Knife Our most popular safety glasses H1300 H1298 G7984 H2347 H0736Maintenance Belt CleaningSchedule LubricationService Troubleshooting GuideCutting Inspecting Knives Adjusting/Replacing KnivesTo inspect the knives To adjust/replace the knives Tools Needed QtyPage Checking/Adjusting Table Parallelism To check the outfeed table parallelismTo adjust the table parallelism To check the infeed table parallelismSetting Outfeed Table Height To set the outfeed table heightSetting Infeed Table Positive stop bolts for infeed tableSetting Fence Stops Calibrating DepthScale To calibrate the depth scaleTo set the 90˚ fence stop To set the 45 outward fence stopWiring Diagram Electrical Components Jointer Parts Breakdown Jointer Parts List DescriptionBumper Stand/Motor Parts Breakdown Stand/Motor Parts List PLABEL-29 Cutterhead Guard Label Warranty and Returns G0604 6 X 56 Jointer Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog
Top Page Image Contents