Grizzly G0604 owner manual Squaring Stock, Minimum dimensions for edge Jointing

Page 25

•Remove foreign objects from the stock. Make sure that any stock you process with the jointer is clean and free of any dirt, nails, staples, tiny rocks or any other foreign objects that may damage the jointer blades.

•Only process natural wood fiber through your jointer. Never joint MDF, particle board, plywood, laminates or other synthetically made materials.

•Make sure all stock is sufficiently dried before jointing. Wood with a moisture con- tent over 20% will cause unnecessary wear on the knives and poor cutting results.

•Make sure your workpiece exceeds the minimum dimension requirements (Figures 26 & 27) before edge jointing or surface planing, or it may break or kick back during the operation!

Squaring Stock

Squaring stock involves four steps performed in the order below:

1.Surface Plane On The Jointer—The con- cave face of the workpiece is surface planed flat with the jointer.

2.Surface Plane On a Thickness Planer—The opposite face of the workpiece is surface planed

flat with a thickness planer.

10" Min.

1" Min.

1⁄2" Min.

Figure 26. Minimum dimensions for edge

jointing.

10" Min.

1⁄2" Min.

1" Min.

Figure 27. Minimum dimensions for surface

planing.

Previously

Surface

Planed Face

3.Edge Joint On The Jointer—The concave edge of the workpiece is jointed flat with the jointer.

4.Rip Cut On A Table Saw—The jointed edge of the workpiece is placed against a table saw fence and the opposite edge cut off.

Previously

Jointed Edge

��

��

��

G0604 6" X 56" Jointer

-23-

Image 25

Contents Model G0604 Page Table of Contents Warranty and Returns Foreword IntroductionContact Info Machine Data Sheet Identification Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Jointers 110V Operation Circuit RequirementsSetup Safety SetupItems Needed for Setup UnpackingAssembly Fasteners Qty Stand Assembly w/MotorInventory Jointer Box Figure QtyHardware Recognition Chart Wheel Assembly CleanupSite Considerations Components and Hardware Needed QtyJointerV-Belt To install the V-beltTo mount the jointer to the stand To check the outfeed table height Checking Outfeed Table HeightSetting Outfeed Table Height on To install the extension tableExtension Table Fence To install the fenceTo install the cutterhead guard Pedestal SwitchTo install the pedestal switch Cutterhead GuardDust Port Knife Setting JigTest Run Recommended Factory adjustments that should be verifiedOperations Operation Safety Basic ControlsStart & Stop Buttons Figure Tilt lock and plunger locations Stock Inspection and RequirementsSquaring Stock Minimum dimensions for edge JointingTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingH9218-6 Byrd Shelix Cutterhead AccessoriesG3631-Jointer/Planer Knife Hone Dispoz-A-BladeHolder and Knife H1300 H1298 G7984 H2347 H0736 Our most popular safety glassesBelt Cleaning MaintenanceSchedule LubricationTroubleshooting Guide ServiceCutting Inspecting Knives Adjusting/Replacing KnivesTo inspect the knives Tools Needed Qty To adjust/replace the knivesPage To check the outfeed table parallelism Checking/Adjusting Table ParallelismTo check the infeed table parallelism To adjust the table parallelismTo set the outfeed table height Setting Outfeed Table HeightPositive stop bolts for infeed table Setting Infeed TableCalibrating Depth Setting Fence StopsScale To calibrate the depth scaleTo set the 45 outward fence stop To set the 90˚ fence stopWiring Diagram Electrical Components Jointer Parts Breakdown Description Jointer Parts ListBumper Stand/Motor Parts Breakdown Stand/Motor Parts List PLABEL-29 Cutterhead Guard Label Warranty and Returns G0604 6 X 56 Jointer Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog