Grizzly G0604 owner manual Safety Instructions for Machinery

Page 8

SECTION 1: SAFETY

For Your Own Safety, Read Instruction Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

	Indicates an imminently hazardous situation which, if not avoided,

	WILL result in death or serious injury.
	Indicates a potentially hazardous situation which, if not avoided,
	COULD result in death or serious injury.
	Indicates a potentially hazardous situation which, if not avoided,
	MAY result in minor or moderate injury. It may also be used to alert
	against unsafe practices.
NOTICE	This symbol is used to alert the user to useful information about
NOTICE	proper operation of the machine.

Safety Instructions for Machinery

1.READ THROUGH THE ENTIRE MANUAL BEFORE STARTING MACHINERY. Machinery presents serious injury hazards to untrained users.

2.ALWAYS USE ANSI APPROVED SAFETY GLASSES WHEN OPERATING MACHINERY. Everyday eyeglasses only have impact resistant lenses—they are NOT safety glasses.

3.ALWAYS WEAR AN ANSI APPROVED RESPIRATOR WHEN OPERATING MACHINERY THAT PRODUCES DUST. Wood dust is a carcinogen and can cause cancer and severe respiratory illnesses.

4.ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage.

5.WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts. Wear protective hair covering to con- tain long hair and wear non-slip footwear.

6.NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. Be mentally alert at all times when running machinery.

-6-	G0604 6" X 56" Jointer

Image 8

Contents Model G0604 Page Table of Contents Warranty and Returns Contact Info IntroductionForeword Machine Data Sheet Identification Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Jointers Circuit Requirements 110V OperationSetup Setup SafetyItems Needed for Setup UnpackingStand Assembly w/Motor Assembly Fasteners QtyInventory Jointer Box Figure QtyHardware Recognition Chart Cleanup Wheel AssemblySite Considerations Components and Hardware Needed QtyTo mount the jointer to the stand To install the V-beltJointerV-Belt Checking Outfeed Table Height To check the outfeed table heightExtension Table To install the extension tableSetting Outfeed Table Height on To install the fence FencePedestal Switch To install the cutterhead guardTo install the pedestal switch Cutterhead GuardKnife Setting Jig Dust PortFactory adjustments that should be verified Test Run RecommendedStart & Stop Buttons Figure Operation Safety Basic ControlsOperations Stock Inspection and Requirements Tilt lock and plunger locationsMinimum dimensions for edge Jointing Squaring StockSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerG3631-Jointer/Planer Knife Hone AccessoriesH9218-6 Byrd Shelix Cutterhead Dispoz-A-BladeHolder and Knife Our most popular safety glasses H1300 H1298 G7984 H2347 H0736Maintenance Belt CleaningSchedule LubricationService Troubleshooting GuideCutting To inspect the knives Adjusting/Replacing KnivesInspecting Knives To adjust/replace the knives Tools Needed QtyPage Checking/Adjusting Table Parallelism To check the outfeed table parallelismTo adjust the table parallelism To check the infeed table parallelismSetting Outfeed Table Height To set the outfeed table heightSetting Infeed Table Positive stop bolts for infeed tableSetting Fence Stops Calibrating DepthScale To calibrate the depth scaleTo set the 90˚ fence stop To set the 45 outward fence stopWiring Diagram Electrical Components Jointer Parts Breakdown Jointer Parts List DescriptionBumper Stand/Motor Parts Breakdown Stand/Motor Parts List PLABEL-29 Cutterhead Guard Label Warranty and Returns G0604 6 X 56 Jointer Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog