Grizzly G0604 owner manual Knife Setting Jig, Dust Port

Page 21

Knife Setting Jig

Components and Hardware Needed:	Qty
Knife Setting Jig Rod	1
Knife Setting Jig Foot	2
E-Clip	4

Assemble the knife setting jig as shown in Figure 19.

Figure 19. Knife setting jig assembly.

Dust Port
Components and Hardware Needed:	Qty
Dust Port	1
Phillips Screws M5-.8 x 16	4
Flat Washers 5mm	4

Install the dust port as shown in Figure 20.

Figure 20. Installing dust port.

DO NOT operate the Model G0604 with- out an adequate dust collection system. This machine creates substantial amounts of wood dust while operating. Failure to use a dust collection system can result in short and long-term respiratory illness.

Recommended CFM at Dust Port: 400 CFM

Do not confuse this CFM recommendation with the rating of the dust collector. To determine the CFM at the dust port, you must take into account many variables, including the CFM rating of the dust collector, the length of hose between the dust collector and the machine, the amount of branches or wyes, and the amount of other open lines throughout the system. Explaining this cal- culation is beyond the scope of this manual. If you are unsure of your system, consult an expert or purchase a good dust collection "how-to" book.

G0604 6" X 56" Jointer

-19-

Image 21

Contents Model G0604 Page Table of Contents Warranty and Returns Introduction ForewordContact Info Machine Data Sheet Identification Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Jointers 110V Operation Circuit RequirementsSetup Safety SetupItems Needed for Setup UnpackingAssembly Fasteners Qty Stand Assembly w/MotorInventory Jointer Box Figure QtyHardware Recognition Chart Wheel Assembly CleanupSite Considerations Components and Hardware Needed QtyTo install the V-belt JointerV-BeltTo mount the jointer to the stand To check the outfeed table height Checking Outfeed Table HeightTo install the extension table Setting Outfeed Table Height onExtension Table Fence To install the fenceTo install the cutterhead guard Pedestal SwitchTo install the pedestal switch Cutterhead GuardDust Port Knife Setting JigTest Run Recommended Factory adjustments that should be verifiedOperation Safety Basic Controls OperationsStart & Stop Buttons Figure Tilt lock and plunger locations Stock Inspection and RequirementsSquaring Stock Minimum dimensions for edge JointingTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingAccessories H9218-6 Byrd Shelix CutterheadG3631-Jointer/Planer Knife Hone Dispoz-A-BladeHolder and Knife H1300 H1298 G7984 H2347 H0736 Our most popular safety glassesBelt Cleaning MaintenanceSchedule LubricationTroubleshooting Guide ServiceCutting Adjusting/Replacing Knives Inspecting KnivesTo inspect the knives Tools Needed Qty To adjust/replace the knivesPage To check the outfeed table parallelism Checking/Adjusting Table ParallelismTo check the infeed table parallelism To adjust the table parallelismTo set the outfeed table height Setting Outfeed Table HeightPositive stop bolts for infeed table Setting Infeed TableCalibrating Depth Setting Fence StopsScale To calibrate the depth scaleTo set the 45 outward fence stop To set the 90˚ fence stopWiring Diagram Electrical Components Jointer Parts Breakdown Description Jointer Parts ListBumper Stand/Motor Parts Breakdown Stand/Motor Parts List PLABEL-29 Cutterhead Guard Label Warranty and Returns G0604 6 X 56 Jointer Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog