Grizzly G0604 owner manual Tools Needed Qty, To adjust/replace the knives

Page 36

Knife Setting Jig Method: Both tables are low- ered to fit the jig on the cutterhead, as shown in Figure 47, and the knife heights are set to just touch the middle pad of the jig.

The knife setting jig makes it easy to ensure that the knives project out of the cutterhead evenly. After using the knife setting jig to set the knives, you have to re-adjust the outfeed table height to ensure that it is even with the knives at their high- est point of rotation. If you use the positive stops on the tables, reset them before operation.

Figure 47. Using knife setting jig to set knife

height.

The Model G0604 comes with both jack screws and springs inside the cutterhead to provide two options for adjusting the knives (see Figure 48). Note: Only one of these options is needed to set the knives—seeStep 5 for clarification.

Figure 48. Cutterhead profile diagram.

Tools Needed

Qty

Straightedge

1

Knife Setting Jig (Optional)

1

Hex Wrench 4mm

1

Wrench 10mm

1

To adjust/replace the knives:

 

1.DISCONNECT JOINTER FROM POWER SOURCE!

2.Remove the cutterhead guard from the table and move the fence back as far as it will go.

3.Remove the belt guard to expose the cutterhead pulley.

4.Rotate the cutterhead pulley to get access to one of the cutterhead knives.

5.Loosen the cutterhead gib bolts, starting in the middle, and alternating back and forth until all of the gib bolts are loose, but not fall- ing out.

—If this is the first time you are setting the knives, remove the gib and knife from the cutterhead. Decide which adjustment option you are going to use between the jack screws and the springs.

—If you decide to use the jack screws, remove the springs from the cutterhead (they are located directly below the knives).

—If you decide to use the springs, just thread the jack screws completely into the cutterhead so they will not get lost. Replace the gib and knife.

-34-

G0604 6" X 56" Jointer

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Model G0604 Page Table of Contents Warranty and Returns Introduction ForewordContact Info Machine Data Sheet Identification Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Jointers Circuit Requirements 110V OperationSetup Setup SafetyItems Needed for Setup UnpackingStand Assembly w/Motor Assembly Fasteners QtyInventory Jointer Box Figure QtyHardware Recognition Chart Cleanup Wheel AssemblySite Considerations Components and Hardware Needed QtyTo install the V-belt JointerV-BeltTo mount the jointer to the stand Checking Outfeed Table Height To check the outfeed table heightTo install the extension table Setting Outfeed Table Height onExtension Table To install the fence FencePedestal Switch To install the cutterhead guardTo install the pedestal switch Cutterhead GuardKnife Setting Jig Dust PortFactory adjustments that should be verified Test Run RecommendedOperation Safety Basic Controls OperationsStart & Stop Buttons Figure Stock Inspection and Requirements Tilt lock and plunger locationsMinimum dimensions for edge Jointing Squaring StockSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerAccessories H9218-6 Byrd Shelix CutterheadG3631-Jointer/Planer Knife Hone Dispoz-A-BladeHolder and Knife Our most popular safety glasses H1300 H1298 G7984 H2347 H0736Maintenance Belt CleaningSchedule LubricationService Troubleshooting GuideCutting Adjusting/Replacing Knives Inspecting KnivesTo inspect the knives To adjust/replace the knives Tools Needed QtyPage Checking/Adjusting Table Parallelism To check the outfeed table parallelismTo adjust the table parallelism To check the infeed table parallelismSetting Outfeed Table Height To set the outfeed table heightSetting Infeed Table Positive stop bolts for infeed tableSetting Fence Stops Calibrating DepthScale To calibrate the depth scaleTo set the 90˚ fence stop To set the 45 outward fence stopWiring Diagram Electrical Components Jointer Parts Breakdown Jointer Parts List DescriptionBumper Stand/Motor Parts Breakdown Stand/Motor Parts List PLABEL-29 Cutterhead Guard Label Warranty and Returns G0604 6 X 56 Jointer Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog
Top Page Image Contents