Grizzly G0604 owner manual Machine Data Sheet

Page 6

Machine Data Sheet

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901

MODEL G0604 6" X 56" Jointer

Design Type:	Floor Model
Overall Dimensions:
Table Size	6" W x 551⁄2" L
Height (from floor to table)	321⁄2"
Table Length	551⁄2"
Table Width	6"
Shipping Weight	347 lbs.
Net Weight	320 lbs.
1st Box Size	29"L x 18"W x 28"H
2nd Box Size	62"L x 21"W x 14"H
Stand Footprint	27"W x 201⁄2"D
Cutterhead	4-Knife
Cutterhead Diameter	3"
Cutterhead Knife Size	6" x 3⁄4" x 1⁄8"
Capacities:
Maximum Depth of Cut (per pass)	1⁄8"
Maximum Width of Cut	6"
Cutterhead Speed	4850 RPM
Cuts Per Minute	19,400
Construction:
Tables	Precision Ground Cast Iron
Fence Assembly	Cast Iron
Body Assembly	Cast Iron
Stand	Preformed Steel
Guard	Aluminum
Bearings	Shielded and Lubricated
Motor:
Type	TEFC Capacitor Start Induction
Horsepower	1 HP
Phase ⁄ Voltage	Single-Phase / 110V
Amps	13A
Cycle ⁄ RPM	60 Hertz / 3450 RPM
Power Transfer	Belt Drive
Bearings	Shielded and Lubricated
Sound Rating	80 dB
Features:
...................................................................................	Parallelogram Table Adjustment
...........................................................................................	Top Mount Switch Controls
......................................................................................	Fence Stops at 45°, 90°, 135°
....................................................................................................	Included 4" Dust Port
....................................................................................................	Included Push Blocks
.............................................................................................	Included Knife Setting Jig

Specifications, while deemed accurate, are not guaranteed.

-4-	G0604 6" X 56" Jointer

Image 6

Contents Model G0604 Page Table of Contents Warranty and Returns Introduction ForewordContact Info Machine Data Sheet Identification Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Jointers Circuit Requirements 110V OperationItems Needed for Setup SetupSetup Safety UnpackingInventory Stand Assembly w/MotorAssembly Fasteners Qty Jointer Box Figure QtyHardware Recognition Chart Site Considerations CleanupWheel Assembly Components and Hardware Needed QtyTo install the V-belt JointerV-BeltTo mount the jointer to the stand Checking Outfeed Table Height To check the outfeed table heightTo install the extension table Setting Outfeed Table Height onExtension Table To install the fence FenceTo install the pedestal switch Pedestal SwitchTo install the cutterhead guard Cutterhead GuardKnife Setting Jig Dust PortFactory adjustments that should be verified Test Run RecommendedOperation Safety Basic Controls OperationsStart & Stop Buttons Figure Stock Inspection and Requirements Tilt lock and plunger locationsMinimum dimensions for edge Jointing Squaring StockSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerAccessories H9218-6 Byrd Shelix CutterheadG3631-Jointer/Planer Knife Hone Dispoz-A-BladeHolder and Knife Our most popular safety glasses H1300 H1298 G7984 H2347 H0736Schedule MaintenanceBelt Cleaning LubricationService Troubleshooting GuideCutting Adjusting/Replacing Knives Inspecting KnivesTo inspect the knives To adjust/replace the knives Tools Needed QtyPage Checking/Adjusting Table Parallelism To check the outfeed table parallelismTo adjust the table parallelism To check the infeed table parallelismSetting Outfeed Table Height To set the outfeed table heightSetting Infeed Table Positive stop bolts for infeed tableScale Setting Fence StopsCalibrating Depth To calibrate the depth scaleTo set the 90˚ fence stop To set the 45 outward fence stopWiring Diagram Electrical Components Jointer Parts Breakdown Jointer Parts List DescriptionBumper Stand/Motor Parts Breakdown Stand/Motor Parts List PLABEL-29 Cutterhead Guard Label Warranty and Returns G0604 6 X 56 Jointer Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog