Grizzly G0604 Operations, Operation Safety Basic Controls, Start & Stop Buttons Figure

Page 23

SECTION 4: OPERATIONS

Operation Safety		Basic Controls

Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine.

Loose hair and cloth-

ing could get caught in

machinery and cause seri-

ous personal injury. Keep

loose clothing and long

hair away from moving machinery.

Lock the mobile base wheel before operat- ing the jointer! Operating the jointer with the wheel unlocked may cause loss of control, resulting in serious personal injury.

NOTICE

If you have never used this type of machine or equipment before, WE STRONGLY REC- OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training.

G0604 6" X 56" Jointer

This section covers the basic controls used during routine operations.

START & STOP Buttons (Figure 21)

START

Button

STOP

Button

Figure 21. START/STOP button locations.

Table Movement: To move the infeed table, loosen the table lock (Figure 22), move the table with the table lever in the preset range, then tighten the table lock. The outfeed table is preset with no range of movement allowed, so if it gets accidentally unlocked it will not move. To adjust the preset range of movement, refer to SECTION

7:SERVICE about setting table heights.


			Table
	Table		Table		Table
	Table		Locks		Table
	Lever		Locks		Lever
	Lever				Lever

Figure 22. Table control locations.

-21-

Image 23

Contents Model G0604 Page Table of Contents Warranty and Returns Contact Info IntroductionForeword Machine Data Sheet Identification Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Jointers 110V Operation Circuit RequirementsUnpacking SetupSetup Safety Items Needed for SetupJointer Box Figure Qty Stand Assembly w/MotorAssembly Fasteners Qty InventoryHardware Recognition Chart Components and Hardware Needed Qty CleanupWheel Assembly Site ConsiderationsTo mount the jointer to the stand To install the V-beltJointerV-Belt To check the outfeed table height Checking Outfeed Table HeightExtension Table To install the extension tableSetting Outfeed Table Height on Fence To install the fenceCutterhead Guard Pedestal SwitchTo install the cutterhead guard To install the pedestal switchDust Port Knife Setting JigTest Run Recommended Factory adjustments that should be verifiedStart & Stop Buttons Figure Operation Safety Basic ControlsOperations Tilt lock and plunger locations Stock Inspection and RequirementsSquaring Stock Minimum dimensions for edge JointingTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingG3631-Jointer/Planer Knife Hone AccessoriesH9218-6 Byrd Shelix Cutterhead Dispoz-A-BladeHolder and Knife H1300 H1298 G7984 H2347 H0736 Our most popular safety glassesLubrication MaintenanceBelt Cleaning ScheduleTroubleshooting Guide ServiceCutting To inspect the knives Adjusting/Replacing KnivesInspecting Knives Tools Needed Qty To adjust/replace the knivesPage To check the outfeed table parallelism Checking/Adjusting Table ParallelismTo check the infeed table parallelism To adjust the table parallelismTo set the outfeed table height Setting Outfeed Table HeightPositive stop bolts for infeed table Setting Infeed TableTo calibrate the depth scale Setting Fence StopsCalibrating Depth ScaleTo set the 45 outward fence stop To set the 90˚ fence stopWiring Diagram Electrical Components Jointer Parts Breakdown Description Jointer Parts ListBumper Stand/Motor Parts Breakdown Stand/Motor Parts List PLABEL-29 Cutterhead Guard Label Warranty and Returns G0604 6 X 56 Jointer Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog