Grizzly G0604 owner manual Maintenance, Schedule, Belt Cleaning, Lubrication

Page 32

SECTION 6: MAINTENANCE

Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury.

Schedule

For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section.

Daily

•Vacuum all dust on and around the machine.

•Wipe down tables and all other unpainted cast iron with a metal protectant.

Monthly Check

•V-belt tension, damage, or wear.

•Clean/vacuum dust buildup from inside cabi- net and off of motor.

V-Belt

Cleaning

Cleaning the Model G0604 is relatively easy. Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth. If any resin has built up, use a resin dissolving cleaner to remove it.

Protect the unpainted cast iron surfaces on the table by wiping the table clean after every use— this ensures moisture from wood dust does not remain on bare metal surfaces.

Keep tables rust-free with regular applications of products like G96® Gun Treatment, SLIPIT®, or Boeshield® T-9 (see Page 28).

Lubrication

Since all bearings are sealed and permanently lubricated, simply leave them alone until they need to be replaced. DO NOT lubricate them.

To ensure optimum power transmission from the motor to the blade, the V-belt must be in good condition (free from cracks, fraying and wear) and properly aligned and tensioned (refer to the instructions on Page 14).

-30-	G0604 6" X 56" Jointer

Image 32

Contents Model G0604 Page Table of Contents Warranty and Returns Contact Info IntroductionForeword Machine Data Sheet Identification Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Jointers Circuit Requirements 110V OperationSetup Setup SafetyItems Needed for Setup UnpackingStand Assembly w/Motor Assembly Fasteners QtyInventory Jointer Box Figure QtyHardware Recognition Chart Cleanup Wheel AssemblySite Considerations Components and Hardware Needed QtyTo mount the jointer to the stand To install the V-beltJointerV-Belt Checking Outfeed Table Height To check the outfeed table heightExtension Table To install the extension tableSetting Outfeed Table Height on To install the fence FencePedestal Switch To install the cutterhead guardTo install the pedestal switch Cutterhead GuardKnife Setting Jig Dust PortFactory adjustments that should be verified Test Run RecommendedStart & Stop Buttons Figure Operation Safety Basic ControlsOperations Stock Inspection and Requirements Tilt lock and plunger locationsMinimum dimensions for edge Jointing Squaring StockSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerG3631-Jointer/Planer Knife Hone AccessoriesH9218-6 Byrd Shelix Cutterhead Dispoz-A-BladeHolder and Knife Our most popular safety glasses H1300 H1298 G7984 H2347 H0736Maintenance Belt CleaningSchedule LubricationService Troubleshooting GuideCutting To inspect the knives Adjusting/Replacing KnivesInspecting Knives To adjust/replace the knives Tools Needed QtyPage Checking/Adjusting Table Parallelism To check the outfeed table parallelismTo adjust the table parallelism To check the infeed table parallelismSetting Outfeed Table Height To set the outfeed table heightSetting Infeed Table Positive stop bolts for infeed tableSetting Fence Stops Calibrating DepthScale To calibrate the depth scaleTo set the 90˚ fence stop To set the 45 outward fence stopWiring Diagram Electrical Components Jointer Parts Breakdown Jointer Parts List DescriptionBumper Stand/Motor Parts Breakdown Stand/Motor Parts List PLABEL-29 Cutterhead Guard Label Warranty and Returns G0604 6 X 56 Jointer Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog