Grizzly Optimize the Infeed Table of Your G0604 Biscuit Joiner
Page 39

Checking Infeed Table

To check the infeed table parallelism:

1.Follow all the steps for checking the outfeed table parallelism to first make sure that the outfeed table is parallel with the cutterhead.

2.Raise the outfeed table higher than the cutterhead.

3.Place the straightedge halfway across the infeed table and halfway over the outfeed table, and adjust the infeed table even with the outfeed table, as shown in Figure 54.

������������

�������������������������

Figure 54. Infeed and outfeed tables set evenly.

4.Place the straightedge in the positions shown in Figure 55. In each position, the straight- edge should sit flat against both the outfeed table and the infeed table.

Figure 55. Straightedge positions for checking

infeed/outfeed table parallelism.

—If the straightedge sits flat against both the infeed and outfeed table, then the tables are parallel. Set both table heights (Pages 38

&39) and replace the cutterhead guard.

—If the straightedge does not sit flat against both the infeed and outfeed table in any of the positions, then follow the Adjusting Table Parallelism instructions.

G0604 6" X 56" Jointer

Adjusting Table Parallelism

For safe and proper cutting results, the tables must be parallel to the cutterhead. Adjusting them to be parallel is a task of precision and patience, and may take up to one hour to complete. Luckily, this is considered a permanent adjustment and should not need to be repeated for the life of the machine.

Due to the complex nature of this task, we rec- ommend that you double check the current table positions to make sure that they really need to be adjusted before starting. Refer to the previous two subsections if you have not just completed them.

The tables have four eccentric bushings under each corner that allow the tables to be adjusted parallel. These eccentric bushings are locked in place by piggybacked set screws (one on top of the other) and adjust when unlocked and rotated.

The correct order for adjusting the table parallel- ism is to first adjust the outfeed table parallel with the cutterhead, then adjust the infeed table paral- lel with the outfeed table.

When setting the outfeed table, all measurements must be made from the cutterhead body—not the knives—or results may get skewed the next time you change knives.

IMPORTANT: The steps below are intended to be performed in succession with the procedures for checking the outfeed and infeed tables, begin- ning on Page 36. DO NOT CONTINUE UNTIL YOU HAVE FOLLOWED THOSE PROCEDURES FIRST!

To adjust the table parallelism:

1.Place the straightedge on the outfeed table so it hangs over the cutterhead, and lower the outfeed table until the straightedge just touches the cutterhead body, as shown in Figure 52 (rotate the cutterhead if neces- sary).

2.Remove the set screw from each of the four eccentric bushings (Figure 56) under the outfeed table, and loosen the set screws underneath those removed set screws.

-37-

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Model G0604 Page Table of Contents Warranty and Returns Introduction ForewordContact Info Machine Data Sheet Identification Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Jointers 110V Operation Circuit RequirementsUnpacking SetupSetup Safety Items Needed for SetupJointer Box Figure Qty Stand Assembly w/MotorAssembly Fasteners Qty InventoryHardware Recognition Chart Components and Hardware Needed Qty CleanupWheel Assembly Site ConsiderationsTo install the V-belt JointerV-BeltTo mount the jointer to the stand To check the outfeed table height Checking Outfeed Table HeightTo install the extension table Setting Outfeed Table Height onExtension Table Fence To install the fenceCutterhead Guard Pedestal SwitchTo install the cutterhead guard To install the pedestal switchDust Port Knife Setting JigTest Run Recommended Factory adjustments that should be verifiedOperation Safety Basic Controls OperationsStart & Stop Buttons Figure Tilt lock and plunger locations Stock Inspection and RequirementsSquaring Stock Minimum dimensions for edge JointingTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingAccessories H9218-6 Byrd Shelix CutterheadG3631-Jointer/Planer Knife Hone Dispoz-A-BladeHolder and Knife H1300 H1298 G7984 H2347 H0736 Our most popular safety glassesLubrication MaintenanceBelt Cleaning ScheduleTroubleshooting Guide ServiceCutting Adjusting/Replacing Knives Inspecting KnivesTo inspect the knives Tools Needed Qty To adjust/replace the knivesPage To check the outfeed table parallelism Checking/Adjusting Table ParallelismTo check the infeed table parallelism To adjust the table parallelismTo set the outfeed table height Setting Outfeed Table HeightPositive stop bolts for infeed table Setting Infeed TableTo calibrate the depth scale Setting Fence StopsCalibrating Depth ScaleTo set the 45 outward fence stop To set the 90˚ fence stopWiring Diagram Electrical Components Jointer Parts Breakdown Description Jointer Parts ListBumper Stand/Motor Parts Breakdown Stand/Motor Parts List PLABEL-29 Cutterhead Guard Label Warranty and Returns G0604 6 X 56 Jointer Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog
Top Page Image Contents