Grizzly G0604 Cleanup, Site Considerations, Wheel Assembly, Components and Hardware Needed Qty

Page 15

Cleanup

The unpainted cast iron surfaces are coated with a waxy oil to protect them from corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. To clean thor- oughly, some parts may need to be removed. For optimum performance from your machine, make sure you clean all moving parts or slid- ing contact surfaces that are coated. Avoid chlorine-based solvents, such as acetone or brake parts cleaner, as they may damage painted surfaces should they come in contact.

Site Considerations

Machine Placement

Consider the jointer dimensions and size of mate- rial to be processed through each machine, and space for auxiliary stands, work tables or other machinery when establishing a location for your jointer. See Figure 4 for the Model G0604 over- head view dimensions.

551⁄2"

25"

Wheel Assembly

Components and Hardware Needed:	Qty
Wheel Assembly	1
Stand Assembly w/Motor	1
Hex Bolt M8-1.25 x 50	1
Flat Washer 8mm	1
Hex Bolts M10-1.5 x 55	2
Flat Washers 10mm	2
Hex Nuts M10-1.5	2
To attach the wheel:

1.Carefully lay the stand on its side so you can access the underside.

2.Bolt the wheel assembly to the stand with the provided hardware as shown in Figure 5.

Figure 4. Model G0604 overhead view	Figure 5. Bolting the wheel assembly to the
dimensions.	stand.
3.	Turn the stand rightside up.

G0604 6" X 56" Jointer

-13-

Image 15

Contents Model G0604 Page Table of Contents Warranty and Returns Introduction ForewordContact Info Machine Data Sheet Identification Safety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Jointers 110V Operation Circuit RequirementsUnpacking SetupSetup Safety Items Needed for SetupJointer Box Figure Qty Stand Assembly w/MotorAssembly Fasteners Qty InventoryHardware Recognition Chart Components and Hardware Needed Qty CleanupWheel Assembly Site ConsiderationsTo install the V-belt JointerV-BeltTo mount the jointer to the stand To check the outfeed table height Checking Outfeed Table HeightTo install the extension table Setting Outfeed Table Height onExtension Table Fence To install the fenceCutterhead Guard Pedestal SwitchTo install the cutterhead guard To install the pedestal switchDust Port Knife Setting JigTest Run Recommended Factory adjustments that should be verifiedOperation Safety Basic Controls OperationsStart & Stop Buttons Figure Tilt lock and plunger locations Stock Inspection and RequirementsSquaring Stock Minimum dimensions for edge JointingTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingAccessories H9218-6 Byrd Shelix CutterheadG3631-Jointer/Planer Knife Hone Dispoz-A-BladeHolder and Knife H1300 H1298 G7984 H2347 H0736 Our most popular safety glassesLubrication MaintenanceBelt Cleaning ScheduleTroubleshooting Guide ServiceCutting Adjusting/Replacing Knives Inspecting KnivesTo inspect the knives Tools Needed Qty To adjust/replace the knivesPage To check the outfeed table parallelism Checking/Adjusting Table ParallelismTo check the infeed table parallelism To adjust the table parallelismTo set the outfeed table height Setting Outfeed Table HeightPositive stop bolts for infeed table Setting Infeed TableTo calibrate the depth scale Setting Fence StopsCalibrating Depth ScaleTo set the 45 outward fence stop To set the 90˚ fence stopWiring Diagram Electrical Components Jointer Parts Breakdown Description Jointer Parts ListBumper Stand/Motor Parts Breakdown Stand/Motor Parts List PLABEL-29 Cutterhead Guard Label Warranty and Returns G0604 6 X 56 Jointer Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog