Miller Electric Auto-Axcess 450 manual Diagnostic LED’s On Wire Feed Module PC6

Page 44

7-6. Wire Feed Module PC6 Diagnostic LED’s And Dip Switch Settings

	1 Wire Feed Module PC6
2	Diagnostic LED’s are visible inside
	unit, located on PC6 mounted on
	the top tray assembly.
	Refer to Section 7-7for information
	on diagnostic LED’s.
	Reinstall top cover after checking
1	diagnostic LED’s.
LED1 LED2	2 Dip Switch S1
	2 Dip Switch S1
	Dip switches are used to identify
	each circuit board on the internal
	network. Dip switch settings are
	different for each circuit board. For
	proper operation, do not change dip
	settings from those shown.

LED3

LED4

217 333-B / 803 251-B

7-7. Diagnostic LED’s On Wire Feed Module PC6

LED	Status	Diagnosis

1	On	Indicates +15 volts dc is present on wire feed module PC6

	Off	Indicates +15 volts dc is not present on wire feed module PC6

2	On	Indicates +5 volts dc is present on wire feed module PC6

	Off	Indicates +5 volts dc is not present on wire feed module PC6

3,4	On	See Network Status Table in Section 7-12

	Off	See Network Status Table in Section 7-12

OM-210 540 Page 40

Image 44

Contents OM-210 540S ProcessesDescription File Advanced Manufacturing SystemsFrom Miller to You Table of Contents − Troubleshooting TroubleshootingSymbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burnsFumes and Gases can be hazardous ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal or Dirt can injure eyesWelding Wire can cause injury Fire or Explosion hazardFalling Unit can cause injury Moving Parts can cause injuryPrincipal Safety Standards California Proposition 65 WarningsEMF Information About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortLE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LE Bruit peut endommager l’ouïe LES Bouteilles peuvent exploser si elles sont endommagéesRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesserLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-210 540 − Installation SpecificationsDimensions And Weight 17-3/32 in 434 mm 17-3/8 in 441 mm 19-3/32 in 485 mmDuty Cycle And Overheating Volt-Ampere Curves100% Duty Cycle At 450 Amperes OverheatingConnection Diagram Selecting a LocationDo not stack units. Beware of tipping Positive + Weld CableRear Panel Receptacles And Supplementary Protectors Connecting To Weld Terminals Incorrect InstallationSelecting Weld Cable Sizes Peripheral Receptacle Functions Function Socket Socket InformationMotor Control Receptacle Functions Electrical Service Guide Hz Three Phase Input Voltage230 400 460 575 136 263 228 356Disconnect Device Input Power Connections Connecting Input PowerWelding Power Source Input Power Connections Remote Program Setting Touch Sensor OperationRemote Program Select Program No Output a Output B Output C− Operation Operational TermsStart WeldCrater PostflowWire Type LED Front Panel Controls See SectionProcess LED Gas Type LEDSTL Front Panel Switches Robot AbbreviationsManufacturer Robot Abbreviation Xxxx Robot Type100 IPM 1000 IPM Robot Calibration ModeSchedule Sample Auto-Calibration Routine For Motoman Robot Robot Auto-Calibration Sample ProgramsActual Motoman Welder Condition File Weld Data Sample Auto-Calibration Routine For Fanuc RobotSample Auto-Calibration Routine For ABB Robot Reset Mode PulseMild Steel Accu-pulseBlowing Out Inside Of Unit − MaintenanceRoutine Maintenance − Safety Precautions for Servicing Shock Hazard from testingServicing Hazards Exploding Parts can cause injuryCalifornia Proposition 65 Warnings − Troubleshooting Set Value ModeDiagnostics Command error Indicates a CRC PCM bus errorIndicates a UIM Indicates RMD demo is doneIndicates a contactor on error Indicates a trigger closed errorRemoving Cover and Measuring Input Capacitor Voltage Process Control Module PC4 Diagnostic LED’s Diagnostic LED’s On Process Control Module PC4Process Control Module PC4 Status DiagnosisDiagnostic LED’s On Wire Feed Module PC6 User Interface Module PC7 Diagnostic LED’s Diagnostic LED’s On User Interface Module PC7LED32 Automation Interface Module PC9 Diagnostic LED’sLED33 Diagnostic LED’s On Automation Interface Module PC9 Input signal on from relay K6 for arc detected Input signal off from relay K6 for no arc detectedInput signal on for aux. relay energized Input signal off for aux. relay energizedNetwork And Module Status LED’s Network Status LED’s Module Status LED’sRed Circuit board is operating normallyTroubleshooting Trouble RemedyOM-210 540 − Electrical Diagrams Circuit Diagram For Welding Power Source Part 1207 903-G Part 1 Circuit Diagram For Welding Power Source Part 2 207 903-G Part 2 Circuit Diagram For 72 Pin Robot Interface 219 266-C Circuit Diagram For Peripheral/Motor Interface 219 267-B − Parts List 16 − FigWindtunnel Assembly LH And RH Windtunnel Assembly LH And RH -1Item Top Tray Assembly Rear Panel Assembly Front Panel Assembly Front Panel Assembly -1ItemDia Part Support ServiceYour distributor also gives To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s