Miller Electric 301 G, DC Routine Maintenance Robin EH64-Powered Units, Every 8 h, Every 50 h

Page 34

8-2. Routine Maintenance (Robin EH64-Powered Units)

Note	Follow the storage procedure in the engine owner’s manual if the unit will not be used for an
	extended period.
		Y Stop engine before maintaining.
		. See also Engine Manual and Maintenance Label for im-
	Recycle	portant start-up, service, and storage information. Ser-
	Recycle	vice engine more often if used in severe conditions.
	engine	vice engine more often if used in severe conditions.
	engine
	fluids.	* To be done by Factory Authorized Service Agent.
		* To be done by Factory Authorized Service Agent.

Every 8 h

Check fluid levels. See Section 5-2.

Wipe up spills.

Every 20 h

Every 25 h

Check and clean spark arrestor screen. See Section 8-4.

Service air cleaner wrapper (foam element). See Section 8-3.

Every 50 h

Clean and tighten weld terminals.

Every 100 h

Change oil. See Section 8-6and maintenance label.

Clean cooling system. See Engine Manual.

Service air cleaner element. See Section 8-3.

Clean and tighten battery connections.

OM-4407 Page 30

Image 34

Contents Processes OM-4407203 236UDescription From Miller to You Table of Contents Options and Accessories Warranty Symbol Usage Arc Welding HazardsEngine Hazards Compressed Air Hazards EMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings Radiation can cause interferenceUN Choc Électrique peut tuer Signification des symboles− Consignes DE Sécurité − Lire Avant Utilisation LES Fumées ET LES GAZ peuvent être dangereuxDES Pièces Chaudes peuvent provoquer des brûlures graves LE Soudage peut provoquer un in- cendie ou une explosionDES Particules Volantes peuvent blesser les yeux LE Bruit peut affecter l’ouïeLA Chaleur DU Moteur peut pro- voquer un incendie ’EXPLOSION DE LA Batterie peutDES Organes Mobiles peuvent provoquer des blessures ’AIR Comprimé peut provoquer des blessuresPrincipales normes de sécurité Information sur les champs électromagnétiquesSymbol Definitions − DefinitionsWeld, Power, And Engine Specifications − SpecificationsDimensions, Weights, and Operating Angles Fuel Consumption While Using Generator Power Fuel Consumption While WeldingDuty Cycle Generator Power CurveExceeding duty cycle can damage unit and void warranty 100% Duty Cycle at 280 Amperes DCCC/DC Stick Mode Stick And MIG Mode Volt-Ampere CurvesCC/AC Stick Mode CV/DC MIG ModeCC/AC TIG Mode TIG Mode Volt-Ampere CurvesCC/DC TIG Mode − Installation Installing Welding GeneratorOil Engine Prestart Checks Robin EH64-Powered UnitsOil Check Oil Fill Engine Prestart Checks Kohler-Powered Units Follow run-in procedure in engine manualRead and follow all instruc Activating The Dry Charge Battery If ApplicableDo not overfill battery cells Charger+ − Connecting The BatteryInstalling Exhaust Pipe Connect negative − cable lastAC/DC Models Connecting To Weld Output TerminalsStop engine DC Only ModelsSelecting Weld Cable Sizes Remote Receptacle InformationAdjusting Wire MIG Weld Puddle Consistency For wetter weld puddle for mild steel− Operating Welding Generator Do not switch under loadFront Panel Controls Process/Contactor Switch Settings Process/Contactor Switch On CC/CV ModelsSwitch Setting Process Output On/Off Control Set Adjust Remote Control Switch Stick Welding Only Remote Amperage/Voltage ControlGenerator Power Receptacles And Circuit Breakers − Operating Auxiliary EquipmentIf unit does not have Gfci re Ceptacles, use Gfci Optional Generator Power ReceptaclesGfci Receptacle Option Current Available in Amperes 240 Receptacle− Maintenance Robin EH64-POWERED Units Maintenance Label Robin EH64-Powered UnitsEvery 20 h Every 25 h Routine Maintenance Robin EH64-Powered UnitsEvery 8 h Every 50 hEvery 500 h Every 200 hEvery 1000 h Servicing Air Cleaner Robin EH64-Powered Units Servicing Optional Spark Arrestor Robin EH64-Powered UnitsOverload Protection Robin EH64-Powered Units Tools NeededRunning engine Close valve and valve capBefore adding oil Tions as necessary, and wipe up fuelIdle Speed Adjustment Adjusting Engine Speed Robin EH64-Powered UnitsWeld/Power Speed Adjustment Routine Maintenance Kohler-Powered Units − Maintenance KOHLER-POWERED UnitsStop engine before maintaining Maintenance Label Kohler-Powered Units Servicing Air Cleaner Kohler-Powered Units Servicing Optional Spark Arrestor Kohler-Powered UnitsFull Tools Needed Adjusting Engine Speed Kohler-Powered Units Overload Protection Kohler-Powered Units Welding Troubleshooting − TroubleshootingTrouble Remedy Generator Power Troubleshooting Engine TroubleshootingIs on Work like a Pro − Electrical Diagrams 209 625-C OM-4407 209 620-B Selecting Equipment − Generator Power GuidelinesGrounding Generator To Truck Or Trailer Frame Earth ground if supplying Grounding When Supplying Building SystemsHow Much Power Does Equipment Require? Amperes x Volts = WattsIndustrial Motors Rating Starting Watts Running Watts Approximate Power Requirements For Industrial MotorsApproximate Power Requirements For Farm/Home Equipment Farm/Home Equipment Rating Starting Watts Running WattsApproximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running WattsSingle-Phase Induction Motor Starting Requirements Power Required To Start MotorHow Much Power Can Generator Supply? KVA/HP x HP x 1000 = Starting AmperageTypical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible Current Load Watts AmperesOM-4407 − Parts List Main Assembly Kohler Engine ShownMain Assembly Dia Part Description Quantity Mkgs 206537 Panel, Front w/Components Panel, Front w/Components -1Item Generator -1Item Page Page Service SupportOwner’s Record Miller Electric Mfg. Co