Miller Electric Trailblazer DC, 301 G, DC Approximate Power Requirements For Contractor Equipment

Page 57

12-7. Approximate Power Requirements For Contractor Equipment

Contractor	Rating	Starting Watts	Running Watts

Hand Drill	1/4 in	350	350
	3/8 in	400	400
	1/2 in	600	600
Circular Saw	6-1/2 in	500	500
	7-1/4 in	900	900
	8-1/4 in	1400	1400
Table Saw	9 in	4500	1500
	10 in	6300	1800
Band Saw	14 in	2500	1100
Bench Grinder	6 in	1720	720
	8 in	3900	1400
	10 in	5200	1600
Air Compressor	1/2 HP	3000	1000
	1 HP	6000	1500
	1-1/2 HP	8200	2200
	2 HP	10500	2800
Electric Chain Saw	1-1/2 HP, 12 in	1100	1100
	2 HP, 14 in	1100	1100
Electric Trimmer	Standard 9 in	350	350
	Heavy Duty 12 in	500	500
Electric Cultivator	1/3 HP	2100	700
Elec. Hedge Trimmer	18 in	400	400
Flood Lights	HID	125	100
	Metal Halide	313	250
	Mercury	1000
	Sodium	1400
	Vapor	1250	1000
Submersible Pump	400 gph	600	200
Centrifugal Pump	900 gph	900	500
Floor Polisher	3/4 HP, 16 in	4500	1400
	1 HP, 20 in	6100	1600
High Pressure Washer	1/2 HP	3150	950
	3/4 HP	4500	1400
	1 HP	6100	1600
55 gal Drum Mixer	1/4 HP	1900	700
Wet & Dry Vac	1.7 HP	900	900
	2-1/2 HP	1300	1300

OM-4407 Page 53

Image 57

Contents OM-4407203 236U ProcessesDescription From Miller to You Table of Contents Options and Accessories Warranty Arc Welding Hazards Symbol UsageEngine Hazards Compressed Air Hazards California Proposition 65 Warnings Principal Safety StandardsEMF Information Radiation can cause interference− Consignes DE Sécurité − Lire Avant Utilisation Signification des symbolesUN Choc Électrique peut tuer LES Fumées ET LES GAZ peuvent être dangereuxDES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer un in- cendie ou une explosionDES Pièces Chaudes peuvent provoquer des brûlures graves LE Bruit peut affecter l’ouïeDES Organes Mobiles peuvent provoquer des blessures ’EXPLOSION DE LA Batterie peutLA Chaleur DU Moteur peut pro- voquer un incendie ’AIR Comprimé peut provoquer des blessuresInformation sur les champs électromagnétiques Principales normes de sécurité− Definitions Symbol Definitions− Specifications Weld, Power, And Engine SpecificationsDimensions, Weights, and Operating Angles Fuel Consumption While Welding Fuel Consumption While Using Generator PowerExceeding duty cycle can damage unit and void warranty Generator Power CurveDuty Cycle 100% Duty Cycle at 280 Amperes DCCC/AC Stick Mode Stick And MIG Mode Volt-Ampere CurvesCC/DC Stick Mode CV/DC MIG ModeTIG Mode Volt-Ampere Curves CC/AC TIG ModeCC/DC TIG Mode Installing Welding Generator − InstallationEngine Prestart Checks Robin EH64-Powered Units OilOil Check Oil Fill Follow run-in procedure in engine manual Engine Prestart Checks Kohler-Powered UnitsDo not overfill battery cells Activating The Dry Charge Battery If ApplicableRead and follow all instruc ChargerInstalling Exhaust Pipe Connecting The Battery+ − Connect negative − cable lastStop engine Connecting To Weld Output TerminalsAC/DC Models DC Only ModelsRemote Receptacle Information Selecting Weld Cable SizesFor wetter weld puddle for mild steel Adjusting Wire MIG Weld Puddle ConsistencyDo not switch under load − Operating Welding GeneratorFront Panel Controls Process/Contactor Switch On CC/CV Models Process/Contactor Switch SettingsSwitch Setting Process Output On/Off Control Remote Amperage/Voltage Control Set Adjust Remote Control Switch Stick Welding Only− Operating Auxiliary Equipment Generator Power Receptacles And Circuit BreakersOptional Generator Power Receptacles If unit does not have Gfci re Ceptacles, use GfciGfci Receptacle Option Receptacle Current Available in Amperes 240Maintenance Label Robin EH64-Powered Units − Maintenance Robin EH64-POWERED UnitsEvery 8 h Routine Maintenance Robin EH64-Powered UnitsEvery 20 h Every 25 h Every 50 hEvery 200 h Every 500 hEvery 1000 h Servicing Optional Spark Arrestor Robin EH64-Powered Units Servicing Air Cleaner Robin EH64-Powered UnitsTools Needed Overload Protection Robin EH64-Powered UnitsBefore adding oil Close valve and valve capRunning engine Tions as necessary, and wipe up fuelAdjusting Engine Speed Robin EH64-Powered Units Idle Speed AdjustmentWeld/Power Speed Adjustment − Maintenance KOHLER-POWERED Units Routine Maintenance Kohler-Powered UnitsStop engine before maintaining Maintenance Label Kohler-Powered Units Servicing Optional Spark Arrestor Kohler-Powered Units Servicing Air Cleaner Kohler-Powered UnitsFull Tools Needed Adjusting Engine Speed Kohler-Powered Units Overload Protection Kohler-Powered Units − Troubleshooting Welding TroubleshootingTrouble Remedy Engine Troubleshooting Generator Power TroubleshootingIs on Work like a Pro − Electrical Diagrams 209 625-C OM-4407 209 620-B − Generator Power Guidelines Selecting EquipmentGrounding Generator To Truck Or Trailer Frame How Much Power Does Equipment Require? Grounding When Supplying Building SystemsEarth ground if supplying Amperes x Volts = WattsApproximate Power Requirements For Farm/Home Equipment Approximate Power Requirements For Industrial MotorsIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running WattsContractor Rating Starting Watts Running Watts Approximate Power Requirements For Contractor EquipmentHow Much Power Can Generator Supply? Power Required To Start MotorSingle-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 = Starting AmperageTypical Connections To Supply Standby Power Current Load Watts Amperes Selecting Extension Cord Use Shortest Cord PossibleOM-4407 Main Assembly Kohler Engine Shown − Parts ListMain Assembly Dia Part Description Quantity Mkgs 206537 Panel, Front w/Components Panel, Front w/Components -1Item Generator -1Item Page Page Support ServiceMiller Electric Mfg. Co Owner’s Record