symbol (R) on the toolholder. If inserted correctly,the locking sleeve (P) moves back to the end position and shows a closed lock symbol.
2.Pull on the bit to be sure that it is properly locked.
3.If the chisel groove is not aligned with the symbol, or is not inserted to the complete depth the lock symbol remains open.
To remove the bit, pull back the locking sleeve and pull the bit out.
Inserting and Removing SDS Max® Accessories
D25501, D25602, D25831
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories.
1. | Pull back the locking sleeve (P) and insert the bit shank. The bit |
| shank must be clean. |
2. | Turn the bit slightly until the sleeve snaps back into position. |
Clutch Setting 2 (T) is designed for higher torque applications such as core- bits and deep hole hammerdrilling and is designed to clutch out at a higher torque threshold.
Move the torque control lever (U) to setting 1 or 2 as needed for application. NOTE: Allow the motor housing to rotate a little while changing torque.
Each time the tool is plugged in, it will automatically default to clutch setting 1, the most sensitive setting.
FIG. 5
S
T U
G
V
W
| CTC COMPLETE | TORQUE CONTROL | |||||||
|
|
|
| SDS MAX | |||||
| D25XXX | 1 | 3/4" (44mm) | ||||||
| ROTARY HAMMER | ||||||||
|
|
| SER. |
|
|
|
|
| |
|
|
|
| TO REDUCE | THE RISK OF INJURY, | ||||
| WARNING | USER MUST READ |
| . | |||||
|
|
| EYE, EAR AND | ||||||
| MANUAL. | ALWAYSUSE PROPER |
| USE SIDE HANDLE | |||||
|
| PROTECTION. ALWAYS |
|
| DE | ||||
| RESPIRATORY |
|
|
| LEA EL MANUAL | PARA | |||
| ADVERTENCIA | INSTRUCCIONES |
| ||||||
|
|
| UTILICE | ||||||
|
|
|
| SEGURO. SIEMPRE | OÍDOS Y VÍAS | ||||
| UN FUNCIONAMIENTO | PARA LOS OJOS, |
| LATERAL. | |||||
1 | PROTECCIÓN ADECUADA | UTILICE EL MANGO |
| ||||||
ATORIAS. SIEMPRE |
|
| AFIN DE MINIMISER | ||||||
RESPIR |
|
|
|
|
| LES RISQUES DE | |||
| AVERTISSEMENT | LE GUIDE |
| ||||||
|
|
| L’UTILISATEURDOITLIREUNE PROTECTION | ||||||
| BLESSURES, | .TOUJOURS UTILISER ADÉQUATE. | |||||||
| D’UTILISATION | ET RESPIRATOIRE |
|
| |||||
2 | OCULAIRE, AUDITIVE | LATÉRALE. |
|
|
| ||||
UTILISER LA POIGNÉE |
|
|
|
|
|
| |||
|
|
|
|
|
| Service |
|
| |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| Brush Service |
|
English
3. | Ensure the bit is properly engaged. |
| NOTE: The bit needs to move several centimeters in and out of |
| the tool holder (M) when properly engaged. |
4. | To remove the bit, pull back the locking sleeve and pull the bit |
| out. |
Complete Torque Control (Fig. 5)
D25602
NOTICE: Always turn the tool off before changing torque control settings or damage to tool may result.
The Complete Torque Control (CTC) feature of this tool is designed to provide additional control with a
Electronic Speed and Impact Control (Fig. 5)
D25602, D25831, D25851
The electronic speed and impact control allows the use of smaller drill bits without the risk of bit breakage, hammerdrilling into light and brittle materials without shattering and optimal tool control for precise chipping.
To set the control dial, turn the dial (G) to the desired level. The higher the number, the greater the speed and impact energy. Dial settings make the tool extremely adaptable for many different applications. The required setting depends on the bit size and hardness of material being drilled.
7