Makita GA9020, GA7020 Assembly, Installing side grip handle, Installing or removing wheel guard

Page 5

CAUTION:

For tool with locking screw type wheel guard

Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released.

Switch can be locked in "ON" position for ease of operator comfort during extended use. Apply caution when locking tool in "ON" position and

maintain firm grasp on tool.

To start the tool, simply pull the switch trigger (in the B direction). Release the switch trigger to stop. For continuous operation, pull the switch trigger (in the B

1

2

3

006736

1.Wheel guard

2.Screw

3.Bearing box

direction) and then push in the lock lever (in the A direction). To stop the tool from the locked position, pull the switch trigger fully (in the B direction), then release it.

ASSEMBLY

CAUTION:

Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard around 180 degrees counterclockwise. Be sure to tighten the screw securely. To remove wheel guard, follow the installation procedure in reverse.

For tool with clamp lever type wheel guard

Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.

Installing side grip (handle)

12

3

4

007049

1.Bearing box

2.Wheel guard

3.Nut

4.Lever

006735

CAUTION:

Always be sure that the side grip is installed

securely before operation.

Screw the side grip securely on the position of the tool as shown in the figure.

Installing or removing wheel guard

CAUTION:

When using a depressed center grinding wheel/Multi-disc, flex wheel or wire wheel brush, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator.

1. Nut

1

007050

Loosen the lever on the wheel guard. Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard around to the position shown in the figure. Tighten the lever to fasten the wheel guard. If the lever is too tight or too loose to fasten the wheel guard, loosen or tighten the nut to adjust the tightening of the wheel guard band.

To remove wheel guard, follow the installation procedure in reverse.

5

Image 5
Contents Angle Grinder Meuleuse dAngle Esmeriladora Angular English Original instructions SpecificationsGeneral Safety Rules For All Tools Using. Many accidents are caused by poorly maintained tools Specific Safety RulesMinimum gage for cord Ampere Rating Volts 120 25 ft 50 ft 100 ft 150 ft More Than Not More ThanSwitch action SymbolsFunctional Description Shaft lockInstalling side grip handle AssemblyInstalling or removing wheel guard For tool with locking screw type wheel guardInstalling or removing flex wheel optional accessory Installing or removing abrasive disc optional accessoryOperation Grinding and sanding operationOperation with wire wheel brush optional accessory MaintenanceOperation with wire cup brush optional accessory Replacing carbon brushes AccessoriesWire cup brush Wire wheel brushGrip Lock nut 5/8-40Warranty Policy Makita Limited ONE Year WarrantySpécifications Conservez CE Mode DemploiRègles de sécurité générales Pour Tous LES OutilsUtilisation et entretien des outils De personnes qui nen connaissent pas le mode dutilisationRègles DE Sécurité Particulières Description DU Fonctionnement SymbolesBlocage de larbre InterrupteurInstallation ou retrait du carter de meule Installation de la poignée latérale poignéeAssemblage Pour outil avec carter de meule à levier de serrageOpérations de meulage et de ponçage UtilisationEntretien Remplacement des charbons Accessoires8 2 Politique de garantie Garantie Limitée D’UN AN MakitaNormas Generales DE Seguridad EspecificacionesPara todas las herramientas Guarde Estas InstruccionesUso y cuidado de la herramienta Más de No más de Calibre del cable AWG 10 a Normas Específicas DE Seguridad Advertencias y precauciones12 a 16 a No se recomiendaSímbolos Descripción DEL FuncionamientoBloqueo del eje Accionamiento del interruptorInstalación de la empuñadura lateral mango EnsambleOperación de esmerilado y lijado OperaciónOperación con carda de alambres accesorio opcional MantenimientoReemplazamiento de las escobillas de carbón Accesorios8 2 Política de garantía Page 11-8, Sumiyoshi-cho Anjo, Aichi 446-8502 Japan USA only
Related manuals
Manual 2 pages 19.35 Kb Manual 2 pages 19.29 Kb