Makita GA9020, GA7020, GA7021 instruction manual Accessories, Replacing carbon brushes

Page 8

Replacing carbon brushes

ACCESSORIES

2

1

3

001146

1.Commutator

2.Insulating tip

3.Carbon brush

CAUTION:

These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.

Your tool is supplied with a guard for use with a

When the resin insulating tip inside the carbon brush is exposed to contact the commutator, it will automatically shut off the motor. When this occurs, both carbon brushes should be replaced. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps.

depressed center grinding wheel, multi-disc, flex

wheel and wire wheel brush. If you decide to use

your Makita grinder with approved accessories

which you purchase from your Makita distributor or

factory service center, be sure to obtain and use all

necessary fasteners and guards as recommended in this manual. Your failure to do so could result in personal injury to you and others.

If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.

1

006745

2

1.Brush holder cap

2.Screwdriver

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.

8

Image 8
Contents Angle Grinder Meuleuse dAngle Esmeriladora Angular English Original instructions SpecificationsGeneral Safety Rules For All Tools Specific Safety Rules Using. Many accidents are caused by poorly maintained toolsMinimum gage for cord Ampere Rating Volts 120 25 ft 50 ft 100 ft 150 ft More Than Not More ThanSymbols Switch actionFunctional Description Shaft lockAssembly Installing side grip handleInstalling or removing wheel guard For tool with locking screw type wheel guardInstalling or removing abrasive disc optional accessory Installing or removing flex wheel optional accessoryOperation Grinding and sanding operationOperation with wire wheel brush optional accessory MaintenanceOperation with wire cup brush optional accessory Accessories Replacing carbon brushesWire wheel brush Wire cup brushGrip Lock nut 5/8-40Makita Limited ONE Year Warranty Warranty PolicyConservez CE Mode Demploi SpécificationsRègles de sécurité générales Pour Tous LES OutilsDe personnes qui nen connaissent pas le mode dutilisation Utilisation et entretien des outilsRègles DE Sécurité Particulières Symboles Description DU FonctionnementBlocage de larbre InterrupteurInstallation de la poignée latérale poignée Installation ou retrait du carter de meuleAssemblage Pour outil avec carter de meule à levier de serrageUtilisation Opérations de meulage et de ponçageEntretien Accessoires Remplacement des charbons8 2 Garantie Limitée D’UN AN Makita Politique de garantieEspecificaciones Normas Generales DE SeguridadPara todas las herramientas Guarde Estas InstruccionesUso y cuidado de la herramienta Normas Específicas DE Seguridad Advertencias y precauciones Más de No más de Calibre del cable AWG 10 a12 a 16 a No se recomiendaDescripción DEL Funcionamiento SímbolosBloqueo del eje Accionamiento del interruptorEnsamble Instalación de la empuñadura lateral mangoOperación Operación de esmerilado y lijadoMantenimiento Operación con carda de alambres accesorio opcionalAccesorios Reemplazamiento de las escobillas de carbón8 2 Política de garantía Page USA only 11-8, Sumiyoshi-cho Anjo, Aichi 446-8502 Japan
Related manuals
Manual 2 pages 19.35 Kb Manual 2 pages 19.29 Kb