DeWalt DWE4557 Mounting and Using Flaring Cup Type 11 Wheel, Mounting Flaring CUP Wheel Guard FIG

Page 68

English

USING WIRE CUP BRUSHES AND WIRE WHEELS (FIG. 14) Wire wheels and brushes can be used for removing rust, scale and paint, and for smoothing irregular surfaces.

NOTE: The same precautions should be taken when wire brushing paint as when sanding paint (refer to Precautions To Take When Sanding Paint).

1.Allow the tool to reach full speed before touching the tool to the work surface.

2.Apply minimum pressure to work surface, allowing the tool to operate at high speed. Material removal rate is greatest when the tool operates at high speed.

3.Maintain a 5° to 10° angle between the tool and work surface for wire cup brushes.

4.Maintain contact between the edge of the wheel and the work surface with wire wheels.

5. Continuously move the tool in a forward and

FIG. 14

back motion to avoid creating gouges in

 

the work surface. Allowing the tool to rest

 

on the work surface without moving, or

 

moving the tool in a circular motion causes

5˚–10˚

burning and swirling marks on the work

surface.

 

6.Remove the tool from the work surface before turning the tool off. Allow the tool to stop rotating before setting it down.

CAUTION: Use extra care when working over an edge, as a sudden sharp movement of grinder may be experienced.

Mounting and Using Flaring Cup (Type 11) Wheel

MOUNTING FLARING CUP WHEEL GUARD (FIG. 15)

WARNING: The flaring cup wheel guard is not included with this tool. Flaring cup wheels require proper flanges and guards. 4" (101 mm) flaring cup wheel guard D284934 and 5"–6"

(127–152 mm) flaring cup wheel guard D284936 are available as accessories and include proper flange. Failure to use the proper flange and guard can result in injury resulting from wheel breakage and wheel contact.

1.

Install the guard as shown in Figure 15.

FIG. 15

2.

Guard body should be positioned between

 

 

the spindle and the operator to provide

S

 

maximum operator protection.

 

3.

Securely tighten the two clamping screws

 

 

(S) supplied with the guard.

 

MOUNTING FLARING CUP WHEEL (FIG. 16)

1.Install the flaring cup wheel backing flange, aligning the flats on spindle (T) with the flats on backing flange (O).

2.Thread the flaring cup wheel on spindle by hand, seating wheel against backing flange.

3.Depress the spindle lock button and tighten the wheel by hand.

4.To remove the wheel, reverse the above procedure.

FIG. 16

O

 

T

CAUTION: Failure to properly seat the wheel against backing flange before turning the tool on may result in damage to the tool or the wheel.

NOTE: Adjust the guard skirt so that only 1/8" (3.17 mm) of the wheel is exposed by loosening the bolts, allowing the guard to lengthen. Tighten the guard skirt bolts securely before using the grinder.

68

Page 67 Page 69
Image 68
Page 67 Page 69
Contents Page Page Seguridad Eléctrica Definiciones Normas De seguridadSeguridad DEL Área DE Trabajo Seguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaMantenimiento Normas Específicas DE Seguridad AdicionalesInstrucciones de seguridad para todas las operaciones Causas del retroceso y su prevención por parte del operador Español Advertencias de seguridad adicionales para esmeriladoras Español No recomendadoGuarde Estas Instrucciones Para Futuras Consultas MotorComponentes Montaje Y Ajustes Fijación del mango lateralRotación de la caja de engranajes Fig Instalación de cable con conexión a tierra y enchufeAccesorios y dispositivos para el montaje de los discos Mango Lateral AntivibracionesMontaje Y Extracción DEL Protector Protector de montajeDiscos flaps para lijar Discos para esmerilar Discos de lijar Disco de lija Tuerca de fijaciónCepillos de Copa de Piedra Discos de corte Alambre Operación DEL Gatillo FuncionamientoInterruptor Fig Instalación y utilización de los discos de Instalación DE Discos CON Centro Deprimido FIGBotón DEL Seguro DEL EJE FIG Montaje Y Extracción DE Discos CON CuboMontaje DE LAS Almohadillas DE Respaldo Para Lijar FIG Esmerilado DE Bordes CON Discos DE Esmerilar FIGAcabado DE Superficies CON Discos DE Lijar FIG Precauciones que debe tener en cuenta al lijar pintura RespaldoLuego oprima el botón de bloqueo del USO DE Almohadillas DE Respaldo Para Lijar FIGLimpieza Y Eliminación Montaje y uso de cepillos de alambre y discos de alambreSeguridad Ambiental Instalación DE LA Piedra DE Copa FIG Instalación y utilización de piedras de copaInstalación DE LA Guarda DE LAS Piedras DE Copa FIG Montaje y uso de discos de corte Tipo 1 Utilización DE UNA Piedra DE Copa FIGTrabajo Montaje DEL Protector Cerrado TipoMantenimiento Para el diámetro del cubo de la caja deMontaje DE LOS Discos DE Corte FIG USO DE Ruedas DE CorteLubricación LimpiezaReparaciones AccesoriosVoltaje 220 Frecuencia50 Hz PotenciaDefinições diretrizes De segurança Regras Gerais de SegurançaGuarde Estas Instruções Área DE TrabalhoSegurança Pessoal USO E Cuidados DA FerramentaCausas e prevenção por parte do Utilizador do efeito de coiceAdvertências de segurança comuns a Todos os trabalhos de esmerilhamento, fPortuguês Português Instruções de segurança adicionais para esmerilhadeiras Interferência do disco ou da escova de arame com aTensão Comprimento do cabo de extensão Guarde Todos OS Avisos E Instruções Para Consulta Posterior DescriçãoProteção do Interruptor Eletrônico E-SWITCH Protectiontm FinalidadeEmpunhadura ANTI-VIBRAÇÃO Traseira FIG Sistema DE Expulsão DE PartículasMontagem E Ajustes Como instalar a empunhadura lateralComo girar a caixa de engrenagens Fig Instalação de fio e tomada com conexão à terraAcessórios e dispositivos para a instalação de discos Empunhadura Lateral ANTI-VIBRAÇÃOComo Instalar E Retirar O Protetor Protetor de montagemDiscos para lixar Discos de esmerilhamento Discos de lixamento Discos de arame Pedras de esmeril Discos de corte Funcionamento Operação do GatilhoBloqueio do Veio FIG Bloqueio do veio D é fornecido paraMontagem DE Discos SEM Cubo Montagem E Remoção DE Discos COM CubosEsmerilhamento DE Beiras COM Discos Para Esmerilhar FIG Acabamento DE Superfícies COM Discos Para Lixar FIGInstalação DE Almofadas DE Proteção Para Lixamento FIG Disco de lixa deve entrar em contatoComo Usar Almofadas DE Proteção Para Lixar FIG De trabalhoPrecauções a serem tomadas ao lixar superfícies pintadas Instalação e uso de escovas de arame e discos de arameSegurança Ambiental Limpeza E EliminaçãoComo instalar e usar discos de corte tipo Como Instalar Escovas DE Arame Cônicas E Discos DE ArameComo Usar Escovas DE Arame Cônicas E Discos DE Arame FIG Instalação do Protetor DA Pedra DE Esmeril FIGInstalação e utilização de discos de corte Tipo 1 Instalação DA Pedra DE EsmerilfigComo Usar UM Disco DE Pedra DE Esmeril FIG Frente para trás para evitar a formaçãoComo Instalar UM Protetor Fechado Tipo Como Instalar Discos DE Corte FIGManutenção LubrificaçãoLimpeza ReparosAcessórios Protegendo o Meio Ambiente Coleta seletivaEmpunhadura DE Múltiplos Usos Empunhadura DA Caixa DE EngrenagensEspecificações Definitions Safety Guidelines General Power Tool Safety WarningsWork Area Safety Electrical SafetyService Safety Instructions for ALL OperationsPower Tool USE and Care English Causes and Operator Prevention of Kickback Safety Warnings Specific for Sanding Operations Safety Warnings Specific for Polishing OperationsSafety Warnings Specific For Wire Brushing Operations Additional Safety Warnings for GrindersCross Sectional Area Range Cord in meters mm Not RecommendedSave These Instructions for Future USE DescriptionSwitch Protection Intended USEANTI-VIBRATION Rear Handle FIG Dust Ejection SystemAssembly and Adjustments Installing Grounded Cord Set and PlugWheel Mounting Accessories and Attachments Attaching Side Handle , 2 FIGSwitch Fig Installed on the toolMounting Guard OperationTrigger Operation with LOCK-ON Feature Sanding Flap DiscsTrigger Operation Spindle Lock Button FIGGrinding Wheels Sanding Discs Sanding disc Clamp nutWire Wheels Flaring Cup Stones Cutting Wheels Mounting and Removing Hubbed Wheels Mounting NON-HUBBED WheelsSurface Grinding with Grinding Wheels FIG Edge Grinding with Grinding Wheels FIGUsing Sanding Backing Pads FIG Surface Finishing with Sanding Flap Discs FIGPrecautions To Take When Sanding Paint Mounting and Using Wire Brushes and Wire WheelsEnvironmental Safety Cleaning and DisposalMounting and Using Flaring Cup Type 11 Wheel Install the guard as shown in FigureBurning and swirling marks on the work Mounting Flaring CUP Wheel Guard FIGMounting and Using Cutting Type 1 Wheels Using a Flaring CUP Wheel FIGMounting Closed Type 1 Guard Mounting Cutting Wheels FIGMaintenance Cleaning RepairsAccessories LubricationGear Case Grip SpecificationsProtecting the Environment MAY14 Part No. N399009 Copyright 2012, 2013, 2014 D Ewalt

DWE4557 specifications

The DeWalt DWE4557 is a powerful and robust angle grinder designed to deliver high performance and durability for both professional and DIY enthusiasts. This tool is equipped with a 4.5-inch diameter wheel and is renowned for its efficient performance in heavy-duty applications. One of its key features includes a 13-amp motor that provides a remarkable power output of 2,000 watts, ensuring that it can handle tough materials such as metal and masonry with ease.

One of the standout technologies in the DWE4557 is its electronic kickback brake, which engages in the event of a wheel bind-up. This feature helps to minimize the risk of injury and maximizes user safety by bringing the wheel to a stop quickly. The grinder also boasts a no-volt release switch that prevents the tool from starting unexpectedly when reconnected to a power source—a vital safety consideration for frequent users.

The DWE4557 is designed with user comfort in mind. It has an anti-vibration handle that significantly reduces the amount of vibration felt during operation, allowing for prolonged use without causing discomfort to the user’s hands and arms. The handle can be adjusted for optimal control and comfort, accommodating different user preferences.

Additionally, the angle grinder has an integrated safety guard that can be easily adjusted for convenience and operational versatility. The guard protects the user from debris and sparks while grinding or cutting, thereby enhancing safety during use. The DWE4557 also features a spindle lock for easy wheel changes, making it quick and straightforward to switch between different attachments based on the job at hand.

It is worth noting that the DeWalt DWE4557 is designed for durability. It includes a robust, durable construction that can withstand the rigors of heavy usage, ensuring a long lifespan of the tool. The gear case is also designed for longevity, with a high-performance drive system that ensures consistent and reliable operation.

Overall, the DeWalt DWE4557 is a reliable angle grinder that combines power, performance, and safety features in a compact and durable design. Whether for professional applications or personal projects, this tool is well-equipped to deliver outstanding results in a variety of grinding and cutting tasks.
Top Page Image Contents