Cisco Systems SMNMADPTR manual Upgrading the NME-NAM-120S Application Image Full Image, Configure

Page 13

How to Install, Upgrade, or Downgrade NME-NAM-120S

Upgrading the NME-NAM-120S Application Image (Full Image)

This section provides summary and detailed steps about how to upgrade, downgrade, or re-install the full NME-NAM-120S application image.

SUMMARY STEPS

From the Router CLI

1.Download the required software.

2.service-module integrated-service-engine slot/0 reload

3.service-module integrated-service-engine slot/0 session

From the Service-Module Interface

While the service module reboots, it displays the following prompt:

Enter *** to change boot configuration:

4.Enter ***.

After you enter ***, the NAM should display the bootloader prompt. From this prompt, you can either boot the NAM helper located at a TFTP server or boot the pre-installed helper image in the NAM flash.

–To boot the NAM helper image from a TFTP server, do Steps 5, 6, and 7. Skip Step 8, then do Steps 9, 10, and 11.

–To boot the pre-installed helper image on the NAM compact flash, skip Steps 5, 6, and 7, then do Steps 8 through 11.

5.configure

(and follow the prompts)

6.show config

7.boot helper

8.boot compactflash

Note For NM-NAM, enter boot flash.

At this point, you should be at the helper image menu.

9.Select either option 1 or option 2, and follow the prompts.

10.Select r.

11.Close the session as described in Closing a Session, page 11.

DETAILED STEPS

Step 1 Download the NME-NAM-120S installation-package files (containing a kernel image, a helper image, and the NME-NAM-120S application software files) as follows:

a.Go to the NAM page of the Cisco Software Center website at the following location:

Cisco Branch Routers Series Network Analysis Module (NME-NAM-120S) Installation and Configuration Note, 4.0

	OL-14942-02	13

Image 13

Contents Description Series multi-services and integrated services routersPrerequisites for NME-NAM-120S ContentsRouter Platform IOS Version Minimum Required? Network ModulesConfiguration Upgrade or DowngradeRestrictions for the NME-NAM-120S File ServerMonitoring Traffic Through Internal Interface NAM SoftwareGateway router Hardware InterfacesSetting Up Network Module Interfaces How to Install, Upgrade, or Downgrade NME-NAM-120SFrom the Host-Router CLI Ip unnumbered type numberUsing the commands ip interface internal and ip address Command or Action PurposeExample Examples Using the commands ip interface external and ip addressYou can conduct only one session at a time Opening a SessionFrom the Router CLI Use the following steps to close a session Closing a SessionControl-Shift-6 From the Router promptTypes of NAM Software Upgrades Upgrading or Reinstalling NAM SoftwareNAM Software Images PrerequisitesConfigure From the Service-Module InterfaceShow config Boot helper Boot compactflash Upgrading the NME-NAM-120S Application Image Full ImageSession into the NME-NAM-120S console Locate the following fileEnter boot helper Optional Verify your bootloader configuration settingsEnter boot flash Upgrading the NAM Application Image Patch Upgrading the NAM Helper Image NAM CLI Because the exit command closes the session Exit the NAM CLI prompt and get to the NAM loginFTP server must be reachable from NAM CLI Download and save the NAM helper image to the NAMFrom the Router Enable exec Mode Prompt This section describes how to upgrade the NAM helper imageFrom the Service Module Interface Upgrading the NAM Helper ImageBreak to the NAM bootloader prompt Reboot the NAMConfigure the bootloader to load Address, NAM default gatewayReboot the NAM. By default the NAM will Configuring the NME-NAM-120S for ManagementBoot to the NAM application image Download helper image from FTP serverEnter IOS configuration from terminal Enter IOS exec modeEnter IOS interface configuration mode For the integrated-service-engineExit the router configuration mode Setup a full 32-bit static route forNAM management address Callout Interface Location Router Configuration Cisco IOS SoftwareNAM Configuration NAM Software For the integrated-service-engine interface Enter the IOS interface configuration modeIntegrated-service-engine interface Bring up the integrated-service-engineRouter Configuration Cisco IOS Software Configuring the External Interface for Management Enter IOS configuration from terminal Enter IOS exec modeEnable the loopback interface Exit from interface configuration modeAddress Setup the NAM default gatewayCallout Interface Location Login authentication list-name End Show running-config Disabling AAA Login Authentication on the NAM Console LineEnter your password if prompted Enables privileged Exec modeEnters global configuration mode Creates a local authentication listShow ip Ip interface internal externalOptional Configures the NAM system broadcast address Configures the NAM system IP addressConfigures the NAM system default gateway address Optional Enables outside loginsThis section provides the following examples Configuring the NME-NAM-120SEnabling NAM Packet Monitoring Sample Output for the show ip NAM CLI CommandWhat to Do Next Checking Network Connectivity with PingEnd Show running-config Enable Configure terminal Ip cefAnalysis-module monitoring Switching path and enabled packet monitoring on Verify that you enabled the Cisco Express ForwardingCorrect interfaces This section provides the following exampleIp http server enable or Ip http secure server enable Enabling and Accessing the NAM Traffic AnalyzerEnables the Http secure server HTTPs Enables the Http serverEnter a password Configures a password for the web username Open a Telnet or SSH session to the NAM. SeeEnabling the NAM Traffic Analyzer Accessing the NAM Traffic AnalyzerPassword root Changing the NAM Root PasswordTroubleshooting Tips Resetting the NAM Root Password to the Default ValueChanging the NAM Root Password Verifying the NAM Root PasswordEnter your password if prompted Enables privileged Exec modeOpening and Closing a Telnet or SSH Session to the NAM Reloads the software onSSH Prerequisites Telnet PrerequisitesExit Logout Return to command mode Leaves a subcommand modeTo the NAM and return to the Cisco IOS CLI, complete Shutting Down and Starting Up NME-NAM-120S Managing the NME-NAM-120SConfiguration Mode Command Purpose Verifying System Status Configuring Logging Options and Generating Diagnostics Show trace buffer Additional ReferencesShow trace store TraceRFCs MIBsMIBs MIBs Link RFCs TitleTechnical Assistance Feature Information for Network Analysis ModuleDescription Link Glossary Service or services Service engineEngine Service module NetFlowTelnet SyslogVoIP OL-14942-02