Cisco Systems SMNMADPTR manual Enable Configure terminal Ip cef, Analysis-module monitoring

Page 38

Configuring the NME-NAM-120S For Network Connectivity

SUMMARY STEPS

1.enable

2.configure terminal

3.ip cef

4.interface type slot/port or

interface type slot/wic-slot/port

5.analysis-module monitoring

6.Repeat Step 4 and Step 5 for each interface that you want the NAM to monitor.

7.end

8.show running-config

DETAILED STEPS

 

 

 

Command or Action

Purpose

 

 

 

 

 

 

Step 1

enable

Enables privileged EXEC mode.

 

 

 

 

 

• Enter your password if prompted.

 

 

 

Example:

 

 

 

 

 

Router> enable

 

 

 

 

 

 

 

 

Step 2

configure terminal

Enters global configuration mode.

 

 

 

Example:

 

 

 

 

 

Router# configure terminal

 

 

 

 

 

 

 

 

Step 3

ip cef

Enables the Cisco Express Forwarding switching path.

 

 

 

Example:

 

 

 

 

 

Router(config)# ip cef

 

 

 

 

 

 

 

 

Step 4

interface type slot/port

Selects an interface for configuration.

 

 

 

or

 

 

 

 

 

interface type slot/wic-slot/port

 

 

 

 

 

Example:

 

 

 

 

 

Router(config)# interface serial 0/0

 

 

 

 

 

 

 

 

Step 5

analysis-module monitoring

Enables NAM packet monitoring on the interface.

 

 

 

Example:

 

 

 

 

 

Router(config-if)# analysis-module monitoring

 

 

 

 

 

 

 

 

Step 6

Repeat Step 4 and Step 5 for each interface that you

—

 

 

 

want the NAM to monitor through the internal NAM

 

 

 

 

 

interface.

 

 

 

 

 

 

 

 

 

 

 

 

Cisco Branch Routers Series Network Analysis Module (NME-NAM-120S) Installation and Configuration Note, 4.0

 

 

 

 

 

 

 

 

 

 

 

 

38

 

 

 

OL-14942-02

 

 

 

 

 

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Series multi-services and integrated services routers DescriptionContents Prerequisites for NME-NAM-120SNetwork Modules Router Platform IOS Version Minimum Required?Restrictions for the NME-NAM-120S Upgrade or DowngradeConfiguration File ServerNAM Software Monitoring Traffic Through Internal InterfaceHardware Interfaces Gateway routerFrom the Host-Router CLI How to Install, Upgrade, or Downgrade NME-NAM-120SSetting Up Network Module Interfaces Ip unnumbered type numberExample Command or Action PurposeUsing the commands ip interface internal and ip address Using the commands ip interface external and ip address ExamplesFrom the Router CLI Opening a SessionYou can conduct only one session at a time Control-Shift-6 Closing a SessionUse the following steps to close a session From the Router promptNAM Software Images Upgrading or Reinstalling NAM SoftwareTypes of NAM Software Upgrades PrerequisitesShow config Boot helper Boot compactflash From the Service-Module InterfaceConfigure Upgrading the NME-NAM-120S Application Image Full ImageLocate the following file Session into the NME-NAM-120S consoleEnter boot flash Optional Verify your bootloader configuration settingsEnter boot helper Upgrading the NAM Application Image Patch Upgrading the NAM Helper Image NAM CLI FTP server must be reachable from NAM CLI Exit the NAM CLI prompt and get to the NAM loginBecause the exit command closes the session Download and save the NAM helper image to the NAMFrom the Service Module Interface This section describes how to upgrade the NAM helper imageFrom the Router Enable exec Mode Prompt Upgrading the NAM Helper ImageConfigure the bootloader to load Reboot the NAMBreak to the NAM bootloader prompt Address, NAM default gatewayBoot to the NAM application image Configuring the NME-NAM-120S for ManagementReboot the NAM. By default the NAM will Download helper image from FTP serverEnter IOS interface configuration mode Enter IOS exec modeEnter IOS configuration from terminal For the integrated-service-engineNAM management address Setup a full 32-bit static route forExit the router configuration mode Router Configuration Cisco IOS Software Callout Interface LocationNAM Configuration NAM Software Integrated-service-engine interface Enter the IOS interface configuration modeFor the integrated-service-engine interface Bring up the integrated-service-engineRouter Configuration Cisco IOS Software Configuring the External Interface for Management Enable the loopback interface Enter IOS exec modeEnter IOS configuration from terminal Exit from interface configuration modeSetup the NAM default gateway AddressCallout Interface Location Disabling AAA Login Authentication on the NAM Console Line Login authentication list-name End Show running-configEnters global configuration mode Enables privileged Exec modeEnter your password if prompted Creates a local authentication listIp interface internal external Show ipConfigures the NAM system default gateway address Configures the NAM system IP addressOptional Configures the NAM system broadcast address Optional Enables outside loginsConfiguring the NME-NAM-120S This section provides the following examplesWhat to Do Next Sample Output for the show ip NAM CLI CommandEnabling NAM Packet Monitoring Checking Network Connectivity with PingAnalysis-module monitoring Enable Configure terminal Ip cefEnd Show running-config Correct interfaces Verify that you enabled the Cisco Express ForwardingSwitching path and enabled packet monitoring on This section provides the following exampleEnabling and Accessing the NAM Traffic Analyzer Ip http server enable or Ip http secure server enableEnter a password Configures a password for the web username Enables the Http serverEnables the Http secure server HTTPs Open a Telnet or SSH session to the NAM. SeeAccessing the NAM Traffic Analyzer Enabling the NAM Traffic AnalyzerChanging the NAM Root Password Password rootChanging the NAM Root Password Resetting the NAM Root Password to the Default ValueTroubleshooting Tips Verifying the NAM Root PasswordOpening and Closing a Telnet or SSH Session to the NAM Enables privileged Exec modeEnter your password if prompted Reloads the software onExit Logout Telnet PrerequisitesSSH Prerequisites To the NAM and return to the Cisco IOS CLI, complete Leaves a subcommand modeReturn to command mode Managing the NME-NAM-120S Shutting Down and Starting Up NME-NAM-120SConfiguration Mode Command Purpose Verifying System Status Configuring Logging Options and Generating Diagnostics Show trace store Additional ReferencesShow trace buffer TraceMIBs MIBs Link MIBsRFCs RFCs TitleDescription Link Feature Information for Network Analysis ModuleTechnical Assistance Glossary Engine Service module Service engineService or services NetFlowVoIP SyslogTelnet OL-14942-02
Top Page Image Contents