Cisco Systems SMNMADPTR Opening and Closing a Telnet or SSH Session to the NAM, NME-NAM-120S

Page 45

Configuring the NME-NAM-120S For Network Connectivity

DETAILED STEPS

 

Command or Action

Purpose

Step 1

 

 

enable

Enables privileged EXEC mode.

 

 

Enter your password if prompted.

 

Example:

 

 

Router> enable

 

Step 2

 

 

service-module integrated-service-engine slot/0

Reloads the software on the

 

password-reset

NME-NAM-120S.

 

(or for the NM-NAM)

 

 

analysis-module slot/0 password-reset

 

 

Example:

 

 

Router# service-module integrated-service-engine 1/0

 

 

password-reset

 

 

 

 

Troubleshooting Tips

If you have trouble opening a NAM console session from the router, ensure that the NAM console line is clear by entering the service-moduleanalysis-moduleslot/0 session clear command in privileged EXEC mode.

What to Do Next

Verify that the default root password of root is accepted by performing the steps described in the “Closing a Session” section on page 11.

To change the NAM root password, see the “Changing the NAM Root Password” section on page 43.

Opening and Closing a Telnet or SSH Session to the NAM

This procedure opens and closes a Telnet or SSH session to the NAM. This procedure is not commonly performed, because you would typically use the NAM Traffic Analyzer (web GUI) to monitor and maintain the NAM. If, however, you cannot access the NAM Traffic Analyzer, then you might want to use Telnet or SSH to troubleshoot from the NAM CLI.

If your NME-NAM-120S is not properly configured for Telnet or SSH access (see the following Prerequisites, page 45 section), then you can open a Telnet session to the router in which the NME-NAM-120S is installed, and then open a NAM console session from the router. See the “Opening a Session” section on page 10.

Prerequisites

Configure the NAM system IP address. Optionally, set the NAM system hostname. See the “Configuring the NME-NAM-120S For Network Connectivity” section on page 34.

Verify NAM network connectivity by performing one of the following ping tests:

From a host beyond the gateway, ping the NAM system IP address.

Cisco Branch Routers Series Network Analysis Module (NME-NAM-120S) Installation and Configuration Note, 4.0

 

OL-14942-02

45

 

 

 

Image 45
Contents Description Series multi-services and integrated services routersPrerequisites for NME-NAM-120S ContentsRouter Platform IOS Version Minimum Required? Network ModulesConfiguration Upgrade or DowngradeRestrictions for the NME-NAM-120S File ServerMonitoring Traffic Through Internal Interface NAM SoftwareGateway router Hardware InterfacesSetting Up Network Module Interfaces How to Install, Upgrade, or Downgrade NME-NAM-120SFrom the Host-Router CLI Ip unnumbered type numberCommand or Action Purpose Using the commands ip interface internal and ip addressExample Examples Using the commands ip interface external and ip addressOpening a Session You can conduct only one session at a timeFrom the Router CLI Use the following steps to close a session Closing a SessionControl-Shift-6 From the Router promptTypes of NAM Software Upgrades Upgrading or Reinstalling NAM SoftwareNAM Software Images PrerequisitesConfigure From the Service-Module InterfaceShow config Boot helper Boot compactflash Upgrading the NME-NAM-120S Application Image Full ImageSession into the NME-NAM-120S console Locate the following fileOptional Verify your bootloader configuration settings Enter boot helperEnter boot flash Upgrading the NAM Application Image Patch Upgrading the NAM Helper Image NAM CLI Because the exit command closes the session Exit the NAM CLI prompt and get to the NAM loginFTP server must be reachable from NAM CLI Download and save the NAM helper image to the NAMFrom the Router Enable exec Mode Prompt This section describes how to upgrade the NAM helper imageFrom the Service Module Interface Upgrading the NAM Helper ImageBreak to the NAM bootloader prompt Reboot the NAMConfigure the bootloader to load Address, NAM default gatewayReboot the NAM. By default the NAM will Configuring the NME-NAM-120S for ManagementBoot to the NAM application image Download helper image from FTP serverEnter IOS configuration from terminal Enter IOS exec modeEnter IOS interface configuration mode For the integrated-service-engineSetup a full 32-bit static route for Exit the router configuration modeNAM management address Callout Interface Location Router Configuration Cisco IOS SoftwareNAM Configuration NAM Software For the integrated-service-engine interface Enter the IOS interface configuration modeIntegrated-service-engine interface Bring up the integrated-service-engineRouter Configuration Cisco IOS Software Configuring the External Interface for Management Enter IOS configuration from terminal Enter IOS exec modeEnable the loopback interface Exit from interface configuration modeAddress Setup the NAM default gatewayCallout Interface Location Login authentication list-name End Show running-config Disabling AAA Login Authentication on the NAM Console LineEnter your password if prompted Enables privileged Exec modeEnters global configuration mode Creates a local authentication listShow ip Ip interface internal externalOptional Configures the NAM system broadcast address Configures the NAM system IP addressConfigures the NAM system default gateway address Optional Enables outside loginsThis section provides the following examples Configuring the NME-NAM-120SEnabling NAM Packet Monitoring Sample Output for the show ip NAM CLI CommandWhat to Do Next Checking Network Connectivity with PingEnable Configure terminal Ip cef End Show running-configAnalysis-module monitoring Switching path and enabled packet monitoring on Verify that you enabled the Cisco Express ForwardingCorrect interfaces This section provides the following exampleIp http server enable or Ip http secure server enable Enabling and Accessing the NAM Traffic AnalyzerEnables the Http secure server HTTPs Enables the Http serverEnter a password Configures a password for the web username Open a Telnet or SSH session to the NAM. SeeEnabling the NAM Traffic Analyzer Accessing the NAM Traffic AnalyzerPassword root Changing the NAM Root PasswordTroubleshooting Tips Resetting the NAM Root Password to the Default ValueChanging the NAM Root Password Verifying the NAM Root PasswordEnter your password if prompted Enables privileged Exec modeOpening and Closing a Telnet or SSH Session to the NAM Reloads the software onTelnet Prerequisites SSH PrerequisitesExit Logout Leaves a subcommand mode Return to command modeTo the NAM and return to the Cisco IOS CLI, complete Shutting Down and Starting Up NME-NAM-120S Managing the NME-NAM-120SConfiguration Mode Command Purpose Verifying System Status Configuring Logging Options and Generating Diagnostics Show trace buffer Additional ReferencesShow trace store TraceRFCs MIBsMIBs MIBs Link RFCs TitleFeature Information for Network Analysis Module Technical AssistanceDescription Link Glossary Service or services Service engineEngine Service module NetFlowSyslog TelnetVoIP OL-14942-02