Cisco Systems SMNMADPTR manual From NAM CLI, Reboot the NAM, Open a connection to the NAM console

Page 20

How to Install, Upgrade, or Downgrade NME-NAM-120S

DETAILED STEPS

 

Command or Action

Purpose

Step 1

 

 

Download the NME-NAM-120S helper image from CCO and load it

Note The FTP server must be reachable

 

to an FTP server.

from NAM CLI.

Step 2

 

 

From the router exec prompt, apply the IOS command:

Reboot the NAM.

 

service-module integrated-service-engine slot/0 reload

 

 

Example:

 

 

Router# service-module integrated-Service-Engine 1/0 reload

 

 

Use reset only to recover from shutdown or failed state

 

 

Warning: May lose data on the hard disc!

 

 

Do you want to reset?[confirm]

 

 

Trying to reset Service Module Integrated-Service-Engine1/0.

 

Step 3

 

 

service-module integrated-Service-Engine slot/0 session

Open a connection to the NAM console.

 

 

Note Pay attention to the messages that

 

Example:

scroll up the screen. When

 

Router# service-module integrated-Service-Engine 1/0 session

prompted to enter ***, do so

 

Trying 172.20.98.151, 2066 ... Open

 

Step 4

 

 

Enter ***

Break to the NAM bootloader prompt.

 

Note If you want to boot the pre-installed helper image, skip Steps 5,

 

 

6 and 7.

 

 

Note If you do Steps 5, 6, and 7, skip Step 8.

 

 

Note Step 5, 6, and 7 are useful in case the pre-installed helper image

 

 

on the NAM flash has been corrupted. These steps reinstall the

 

 

helper image.

 

Step 5

 

 

configure

Configure the bootloader to load and

 

 

launch the helper.

 

 

Note Follow the prompts to enter NME

 

 

address, subnet mask, TFTP server

 

 

address, NAM default gateway

 

 

address, helper image filename.

 

 

Press Enter to accept the

 

 

previously store input that appears

 

 

inside the square brackets.

Step 6

 

 

show config

Verify the bootloader configuration.

Step 7

 

 

boot helper

Boot the NAM helper image that is located

 

 

on the TFTP server.

Step 8

 

 

boot compactflash

Boot the helper image located on the NAM

 

Note Skip this step if you performed Steps 5, 6, and 7.

flash. For NM-NAM, enter boot flash.

 

Note NAM is shipped with a helper

 

 

 

 

image on its flash memory.

 

 

 

Cisco Branch Routers Series Network Analysis Module (NME-NAM-120S) Installation and Configuration Note, 4.0

20

OL-14942-02

 

 

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Series multi-services and integrated services routers DescriptionContents Prerequisites for NME-NAM-120SNetwork Modules Router Platform IOS Version Minimum Required?Upgrade or Downgrade ConfigurationRestrictions for the NME-NAM-120S File ServerNAM Software Monitoring Traffic Through Internal InterfaceHardware Interfaces Gateway routerHow to Install, Upgrade, or Downgrade NME-NAM-120S Setting Up Network Module InterfacesFrom the Host-Router CLI Ip unnumbered type numberExample Command or Action PurposeUsing the commands ip interface internal and ip address Using the commands ip interface external and ip address ExamplesFrom the Router CLI Opening a SessionYou can conduct only one session at a time Closing a Session Use the following steps to close a sessionControl-Shift-6 From the Router promptUpgrading or Reinstalling NAM Software Types of NAM Software UpgradesNAM Software Images PrerequisitesFrom the Service-Module Interface ConfigureShow config Boot helper Boot compactflash Upgrading the NME-NAM-120S Application Image Full ImageLocate the following file Session into the NME-NAM-120S consoleEnter boot flash Optional Verify your bootloader configuration settingsEnter boot helper Upgrading the NAM Application Image Patch Upgrading the NAM Helper Image NAM CLI Exit the NAM CLI prompt and get to the NAM login Because the exit command closes the sessionFTP server must be reachable from NAM CLI Download and save the NAM helper image to the NAMThis section describes how to upgrade the NAM helper image From the Router Enable exec Mode PromptFrom the Service Module Interface Upgrading the NAM Helper ImageReboot the NAM Break to the NAM bootloader promptConfigure the bootloader to load Address, NAM default gatewayConfiguring the NME-NAM-120S for Management Reboot the NAM. By default the NAM willBoot to the NAM application image Download helper image from FTP serverEnter IOS exec mode Enter IOS configuration from terminalEnter IOS interface configuration mode For the integrated-service-engineNAM management address Setup a full 32-bit static route forExit the router configuration mode Router Configuration Cisco IOS Software Callout Interface LocationNAM Configuration NAM Software Enter the IOS interface configuration mode For the integrated-service-engine interfaceIntegrated-service-engine interface Bring up the integrated-service-engineRouter Configuration Cisco IOS Software Configuring the External Interface for Management Enter IOS exec mode Enter IOS configuration from terminalEnable the loopback interface Exit from interface configuration modeSetup the NAM default gateway AddressCallout Interface Location Disabling AAA Login Authentication on the NAM Console Line Login authentication list-name End Show running-configEnables privileged Exec mode Enter your password if promptedEnters global configuration mode Creates a local authentication listIp interface internal external Show ipConfigures the NAM system IP address Optional Configures the NAM system broadcast addressConfigures the NAM system default gateway address Optional Enables outside loginsConfiguring the NME-NAM-120S This section provides the following examplesSample Output for the show ip NAM CLI Command Enabling NAM Packet MonitoringWhat to Do Next Checking Network Connectivity with PingAnalysis-module monitoring Enable Configure terminal Ip cefEnd Show running-config Verify that you enabled the Cisco Express Forwarding Switching path and enabled packet monitoring onCorrect interfaces This section provides the following exampleEnabling and Accessing the NAM Traffic Analyzer Ip http server enable or Ip http secure server enableEnables the Http server Enables the Http secure server HTTPsEnter a password Configures a password for the web username Open a Telnet or SSH session to the NAM. SeeAccessing the NAM Traffic Analyzer Enabling the NAM Traffic AnalyzerChanging the NAM Root Password Password rootResetting the NAM Root Password to the Default Value Troubleshooting TipsChanging the NAM Root Password Verifying the NAM Root PasswordEnables privileged Exec mode Enter your password if promptedOpening and Closing a Telnet or SSH Session to the NAM Reloads the software onExit Logout Telnet PrerequisitesSSH Prerequisites To the NAM and return to the Cisco IOS CLI, complete Leaves a subcommand modeReturn to command mode Managing the NME-NAM-120S Shutting Down and Starting Up NME-NAM-120SConfiguration Mode Command Purpose Verifying System Status Configuring Logging Options and Generating Diagnostics Additional References Show trace bufferShow trace store TraceMIBs RFCsMIBs MIBs Link RFCs TitleDescription Link Feature Information for Network Analysis ModuleTechnical Assistance Glossary Service engine Service or servicesEngine Service module NetFlowVoIP SyslogTelnet OL-14942-02
Top Page Image Contents