Cisco Systems SMNMADPTR manual Configuring the NME-NAM-120S for Management, Write to NAM flash

Page 21

Configuring the NME-NAM-120S for Management

 

Command or Action

Purpose

Step 9

 

 

Select 4, and follow the prompt to enter a FTP URL

Download helper image from FTP server

 

Main menu

and write to NAM flash.

 

 

 

1

- Download application image and write to HDD

 

 

2

- Download application image and reformat HDD

 

 

3

- Download bootloader and write to flash

 

 

4

- Download helper and write to Compact Flash

 

 

5

- Display software versions

 

 

6

- Reset application image CLI passwords to default

 

 

7

- Change file transfer method (currently ftp/http)

 

 

8

- Show upgrade log

 

 

9

- Send Ping

 

 

f - Format the Flash

 

 

r - Exit and reset Services Engine

 

 

h - Exit and shutdown Services Engine

 

 

Selection [123456789frh]: 4

 

Step 10

 

 

Select r and confirm to reboot the NAM

Reboot the NAM. By default the NAM will

 

 

 

boot to the NAM application image.

Step 11

 

 

Follow the steps described in Closing a Session, page 11 to

Close the NAM console session.

 

close the NAM console session.

 

 

 

 

 

Configuring the NME-NAM-120S for Management

NME-NAM-120S has an internal Gigabit Ethernet interface and an external interface. You can use either interface for NAM management traffic such as the NAM web GUI, telnet or ssh, but not both. You can configure the NAM internal interface to use either IP unnumbered or a routable subnet.

See the following sections for information about how to configure the NME-NAM-120S internal interfaces for management:

•Configuring the Internal Interface for Management—IP Unnumbered, page 21

•Configuring the Internal Interface for Management—Routable Subnet, page 25

•Configuring the External Interface for Management, page 28

Configuring the Internal Interface for Management—IP Unnumbered

This section describes how to configure the NME-NAM-120S internal interface for IP unnumbered.

Note The addresses used for the interface address (Step 4), the NAM-Address (Steps 6 and 9), and the NAM-Default-Gateway-Address (Step 7) must all be in the same subnet.

SUMMARY STEPS

From the Router Prompt

1.enable

2.configure terminal

3.interface integrated-service-engine slot/0

Cisco Branch Routers Series Network Analysis Module (NME-NAM-120S) Installation and Configuration Note, 4.0

 

OL-14942-02

21

 

 

 

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Description Series multi-services and integrated services routersPrerequisites for NME-NAM-120S ContentsRouter Platform IOS Version Minimum Required? Network ModulesConfiguration Upgrade or DowngradeRestrictions for the NME-NAM-120S File ServerMonitoring Traffic Through Internal Interface NAM SoftwareGateway router Hardware InterfacesSetting Up Network Module Interfaces How to Install, Upgrade, or Downgrade NME-NAM-120SFrom the Host-Router CLI Ip unnumbered type numberCommand or Action Purpose Using the commands ip interface internal and ip addressExample Examples Using the commands ip interface external and ip addressOpening a Session You can conduct only one session at a timeFrom the Router CLI Use the following steps to close a session Closing a SessionControl-Shift-6 From the Router promptTypes of NAM Software Upgrades Upgrading or Reinstalling NAM SoftwareNAM Software Images PrerequisitesConfigure From the Service-Module InterfaceShow config Boot helper Boot compactflash Upgrading the NME-NAM-120S Application Image Full ImageSession into the NME-NAM-120S console Locate the following fileOptional Verify your bootloader configuration settings Enter boot helperEnter boot flash Upgrading the NAM Application Image Patch Upgrading the NAM Helper Image NAM CLI Because the exit command closes the session Exit the NAM CLI prompt and get to the NAM loginFTP server must be reachable from NAM CLI Download and save the NAM helper image to the NAMFrom the Router Enable exec Mode Prompt This section describes how to upgrade the NAM helper imageFrom the Service Module Interface Upgrading the NAM Helper ImageBreak to the NAM bootloader prompt Reboot the NAMConfigure the bootloader to load Address, NAM default gatewayReboot the NAM. By default the NAM will Configuring the NME-NAM-120S for ManagementBoot to the NAM application image Download helper image from FTP serverEnter IOS configuration from terminal Enter IOS exec modeEnter IOS interface configuration mode For the integrated-service-engineSetup a full 32-bit static route for Exit the router configuration modeNAM management address Callout Interface Location Router Configuration Cisco IOS SoftwareNAM Configuration NAM Software For the integrated-service-engine interface Enter the IOS interface configuration modeIntegrated-service-engine interface Bring up the integrated-service-engineRouter Configuration Cisco IOS Software Configuring the External Interface for Management Enter IOS configuration from terminal Enter IOS exec modeEnable the loopback interface Exit from interface configuration modeAddress Setup the NAM default gatewayCallout Interface Location Login authentication list-name End Show running-config Disabling AAA Login Authentication on the NAM Console LineEnter your password if prompted Enables privileged Exec modeEnters global configuration mode Creates a local authentication listShow ip Ip interface internal externalOptional Configures the NAM system broadcast address Configures the NAM system IP addressConfigures the NAM system default gateway address Optional Enables outside loginsThis section provides the following examples Configuring the NME-NAM-120SEnabling NAM Packet Monitoring Sample Output for the show ip NAM CLI CommandWhat to Do Next Checking Network Connectivity with PingEnable Configure terminal Ip cef End Show running-configAnalysis-module monitoring Switching path and enabled packet monitoring on Verify that you enabled the Cisco Express ForwardingCorrect interfaces This section provides the following exampleIp http server enable or Ip http secure server enable Enabling and Accessing the NAM Traffic AnalyzerEnables the Http secure server HTTPs Enables the Http serverEnter a password Configures a password for the web username Open a Telnet or SSH session to the NAM. SeeEnabling the NAM Traffic Analyzer Accessing the NAM Traffic AnalyzerPassword root Changing the NAM Root PasswordTroubleshooting Tips Resetting the NAM Root Password to the Default ValueChanging the NAM Root Password Verifying the NAM Root PasswordEnter your password if prompted Enables privileged Exec modeOpening and Closing a Telnet or SSH Session to the NAM Reloads the software onTelnet Prerequisites SSH PrerequisitesExit Logout Leaves a subcommand mode Return to command modeTo the NAM and return to the Cisco IOS CLI, complete Shutting Down and Starting Up NME-NAM-120S Managing the NME-NAM-120SConfiguration Mode Command Purpose Verifying System Status Configuring Logging Options and Generating Diagnostics Show trace buffer Additional ReferencesShow trace store TraceRFCs MIBsMIBs MIBs Link RFCs TitleFeature Information for Network Analysis Module Technical AssistanceDescription Link Glossary Service or services Service engineEngine Service module NetFlowSyslog TelnetVoIP OL-14942-02
Top Page Image Contents