Cisco Systems SMNMADPTR Enter IOS exec mode, Enter IOS configuration from terminal, Mode, Address

Page 22

Configuring the NME-NAM-120S for Management

4.ip unnumber <interface> <number>

5.no shutdown

6.service-module ip address <NAM-Address> <subnetmask>

7.service-module ip default-gateway <NAM-Default-Gateway-Address>

8.exit

9.ip route <NAM-Address> 255.255.255.255 integrated-service-engine slot/0

10.end

DETAILED STEPS

 

Command or Action

Purpose

Step 1

 

 

enable

Enter IOS exec mode.

Step 2

 

 

configure terminal

Enter IOS configuration from terminal

 

 

mode.

Step 3

 

 

interface integrated-service-engine slot/0

Enter IOS interface configuration mode

 

 

for the integrated-service-engine

 

 

interface.

Step 4

 

 

ip unnumber <interface> <number>

Borrow the address that was set at

 

 

<interface>. In the example, interface

 

Example:

integrated-service-engine 1/0 borrows

 

the address set in gigabitethernet0/1

 

Router (config-if)#ip unnumbered gigabitethernet 0/1

 

interface.

 

 

Step 5

 

 

no shutdown

Enable the integrated-service-engine

 

 

interface.

Step 6

 

 

service-module ip address <NAM-Address> <subnetmask>

Set <NAM-Address> to the NAM

 

Router (config-if)#service-module ip address 209.165.200.226

Internal interface.

 

 

 

255.255.255.224

 

Step 7

 

 

service-module ip default-gateway <NAM-Default-Gateway-Address>

Setup the NAM default gateway

 

 

address.

 

Example:

 

 

Router (config-if)#service-module ip default-gateway

 

 

209.165.200.225

 

Step 8

 

 

exit

Exit from the router interface

 

 

configuration mode to the router global

 

 

configuration mode.

 

 

 

Cisco Branch Routers Series Network Analysis Module (NME-NAM-120S) Installation and Configuration Note, 4.0

22

OL-14942-02

 

 

Image 22
Contents Series multi-services and integrated services routers DescriptionContents Prerequisites for NME-NAM-120SNetwork Modules Router Platform IOS Version Minimum Required?Restrictions for the NME-NAM-120S Upgrade or DowngradeConfiguration File ServerNAM Software Monitoring Traffic Through Internal InterfaceHardware Interfaces Gateway routerFrom the Host-Router CLI How to Install, Upgrade, or Downgrade NME-NAM-120SSetting Up Network Module Interfaces Ip unnumbered type numberUsing the commands ip interface internal and ip address Command or Action PurposeExample Using the commands ip interface external and ip address ExamplesYou can conduct only one session at a time Opening a SessionFrom the Router CLI Control-Shift-6 Closing a SessionUse the following steps to close a session From the Router promptNAM Software Images Upgrading or Reinstalling NAM SoftwareTypes of NAM Software Upgrades PrerequisitesShow config Boot helper Boot compactflash From the Service-Module InterfaceConfigure Upgrading the NME-NAM-120S Application Image Full ImageLocate the following file Session into the NME-NAM-120S consoleEnter boot helper Optional Verify your bootloader configuration settingsEnter boot flash Upgrading the NAM Application Image Patch Upgrading the NAM Helper Image NAM CLI FTP server must be reachable from NAM CLI Exit the NAM CLI prompt and get to the NAM loginBecause the exit command closes the session Download and save the NAM helper image to the NAMFrom the Service Module Interface This section describes how to upgrade the NAM helper imageFrom the Router Enable exec Mode Prompt Upgrading the NAM Helper ImageConfigure the bootloader to load Reboot the NAMBreak to the NAM bootloader prompt Address, NAM default gatewayBoot to the NAM application image Configuring the NME-NAM-120S for ManagementReboot the NAM. By default the NAM will Download helper image from FTP serverEnter IOS interface configuration mode Enter IOS exec modeEnter IOS configuration from terminal For the integrated-service-engineExit the router configuration mode Setup a full 32-bit static route forNAM management address Router Configuration Cisco IOS Software Callout Interface LocationNAM Configuration NAM Software Integrated-service-engine interface Enter the IOS interface configuration modeFor the integrated-service-engine interface Bring up the integrated-service-engineRouter Configuration Cisco IOS Software Configuring the External Interface for Management Enable the loopback interface Enter IOS exec modeEnter IOS configuration from terminal Exit from interface configuration modeSetup the NAM default gateway AddressCallout Interface Location Disabling AAA Login Authentication on the NAM Console Line Login authentication list-name End Show running-configEnters global configuration mode Enables privileged Exec modeEnter your password if prompted Creates a local authentication listIp interface internal external Show ipConfigures the NAM system default gateway address Configures the NAM system IP addressOptional Configures the NAM system broadcast address Optional Enables outside loginsConfiguring the NME-NAM-120S This section provides the following examplesWhat to Do Next Sample Output for the show ip NAM CLI CommandEnabling NAM Packet Monitoring Checking Network Connectivity with PingEnd Show running-config Enable Configure terminal Ip cefAnalysis-module monitoring Correct interfaces Verify that you enabled the Cisco Express ForwardingSwitching path and enabled packet monitoring on This section provides the following exampleEnabling and Accessing the NAM Traffic Analyzer Ip http server enable or Ip http secure server enableEnter a password Configures a password for the web username Enables the Http serverEnables the Http secure server HTTPs Open a Telnet or SSH session to the NAM. SeeAccessing the NAM Traffic Analyzer Enabling the NAM Traffic AnalyzerChanging the NAM Root Password Password rootChanging the NAM Root Password Resetting the NAM Root Password to the Default ValueTroubleshooting Tips Verifying the NAM Root PasswordOpening and Closing a Telnet or SSH Session to the NAM Enables privileged Exec modeEnter your password if prompted Reloads the software onSSH Prerequisites Telnet PrerequisitesExit Logout Return to command mode Leaves a subcommand modeTo the NAM and return to the Cisco IOS CLI, complete Managing the NME-NAM-120S Shutting Down and Starting Up NME-NAM-120SConfiguration Mode Command Purpose Verifying System Status Configuring Logging Options and Generating Diagnostics Show trace store Additional ReferencesShow trace buffer TraceMIBs MIBs Link MIBsRFCs RFCs TitleTechnical Assistance Feature Information for Network Analysis ModuleDescription Link Glossary Engine Service module Service engineService or services NetFlowTelnet SyslogVoIP OL-14942-02