Porter-Cable 8101214, PC1800D LED Work Light, Dual Range Gearing Figure G, Keyless Chuck Figure H

Page 10

90550129 PC1800D 4/1/09 2:38 PM Page 10

LED WORK LIGHT

When drill is activated by pulling the trigger switch (1), the integrated LED work light (9) will automatically illuminate the work area.

ADJUSTING TORQUE CONTROL - FIGURE F This tool is fitted with a torque adjustment collar (3) to select the operating mode and to F set the torque for tightening screws. Large screws and hard workpiece materials require a higher torque setting than small screws and soft workpiece materials.

•For drilling in wood, metal and plastics,

set the collar to the drilling position symbol

•For screwdriving, set the collar to the desired setting. If you do not yet know the appropriate setting, proceed as follows:

	4
	1
3	12
3
	10
	8

•Set the collar to the lowest torque setting.

•Tighten the first screw.

•If the clutch ratchets before the desired

result is achieved, increase the collar setting and continue tightening the screw. Repeat until you reach the correct setting. Use this setting for the remaining screws.

DUAL RANGE GEARING - FIGURE G

The dual range feature of your drill allows you to shift gears for greater versatility. To select low speed, high torque setting (position 1), turn tool off and permit to stop. Slide gear shifter button (4) away from the chuck. To select the high speed, low torque setting (position 2), turn tool off and permit to stop. Slide gear shifter button back (towards the chuck).

NOTE: Do not change gears when tool is running. If you are having trouble changing gears, make sure that the dual range gear button is either completely pushed forward or completely pushed back.

KEYLESS CHUCK - FIGURE H

To insert a drill bit or other accessory:

1.Grasp the chuck (5) and rotate it in the counterclockwise direction, as viewed from the chuck end.

2.Insert the bit or other accessory fully into the chuck, and tighten securely by rotating the chuck in the clockwise direction as viewed from the chuck end.

: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur when changing accessories.

G
4
14
12
0
1
8
H

	14
5	12
5
	0
	1
	8

10

Image 10

Contents Advertencia Léase Este Catalog NumberGeneral Power Tool Safety Warnings Specific Safety Rules Safety Guidelines Definitions Important Safety Instructions for Battery Chargers Important Safety Instruction for Battery Packs Charging Procedure Battery CAP InformationStorage Recommendations HOT/COLD Pack Delay Charger DiagnosticsBAD Battery Problem Power LineTrigger Switch & FORWARD/REVERSE Button Figure E Installing and Removing the Battery Pack from the ToolOperating Instructions Dual Range Gearing Figure G LED Work LightKeyless Chuck Figure H On Board BIT Storage MaintenanceScrew Driving DrillingService and Repairs TroubleshootingThree Year Limited Warranty AccessoriesHighway North Jackson, TN 888 DE Catalogue 90550129 PC1800D 4/1/09 238 PM 90550129 PC1800D 4/1/09 238 PM Consignes DE Sécurité Particulières Symboles Lignes Directrices EN Matière DE Sécurité DéfinitionsDescription Fonctionnelle Figure a Lire Toutes LES Directives Information Concernant LE Capuchon DU BLOC-PILE Recommandations EN Matière DE RangementProcédure DE Charge Fonction DE Suspension DU BLOC-PILES CHAUD/FROID Fonctions DE Diagnostic DU ChargeurPile EN Mauvais État Problème Avec LE SecteurDe sécurité et directives perceuses Insertion ET Retrait DU BLOC-PILES DE L’OUTILLampe DE Travail À DEL FonctionnementDétente ET Bouton DE Marche AVANT/MARCHE Arrière Figure E Réglage DU Couple Figure FPerçage DU Bois Mode TournevisMode Perçage Perçage DU MétalDépannage Perçage DE LA MaçonnerieLE Sceau Srprcmc Remarques Spéciales SUR L’EMPLOIAVEC DES Pilesau LithiumEntretien AccessoiresGarantie Limitée DE Trois ANS Pièces DE Rechange Entretien ET RéparationRemplacement DES Étiquettes D’AVERTISSEMENT Catálogo N 90550129 PC1800D 4/1/09 238 PM 90550129 PC1800D 4/1/09 238 PM Normas DE Seguridad Específicas Pautas DE SEGURIDAD/DEFINICIONES SímbolosDescripción DE LAS Funciones Figura aLEA Todas LAS Instrucciones Procedimiento DE Carga Información Acerca DEL Protector DE LA BateríaRecomendaciones CON Respecto AL Almacenamiento Diagnóstico DEL CargadorRetraso POR Paquete CALIENTE/FRÍO Línea DE Potencia CON ProblemasBatería EN MAL Estado Dejar LA Batería EN EL Cargador90550129 PC1800D 4/1/09 238 PM LUZ DE Trabajo DE LED Instrucciones DE OperaciónInterruptor Disparador Y Botón DE AVANCE/REVERSA Figura E Ajuste DEL Control DE Torsión Figura FEspacio EN LA Herramienta Para Guardar Puntas Portabrocas SIN Llave Figura HDestornillado TaladradoTaladrado EN Mampostería Detección DE ProblemasTaladrado EN Metal EL Sello RbrcPiezas DE Repuesto Mantenimiento Y Reparaciones Garantía Limitada DE Tres AñosMantenimiento AccesoriosReemplazo DE LAS Etiquetas DE Advertencia Especificaciones