Black & Decker JS650L instruction manual Hints for Optimum Use, Operating the Laser

Page 8

90501515 JS650L 4/5/06 10:53 AM Page 8

-To switch the tool off, release the switch. To switch the tool off, when in continuous operation, press the switch once more and release it.

OPERATING THE LASER

Your saw is equipped with a laser which is turned on and off separately from the jig saw.

WARNING: NEVER aim the beam at a workpiece with a reflective surface. Bright

shiny reflective sheet steel or similar reflective surfaces are not recommended for laser use. Reflective surfaces could direct the beam back toward the operator.

DANGER: LASER RADIATION. AVOID DIRECT EYE EXPOSURE. Do not stare into the laser light source. Never aim light at another person or object other than the

workpiece. Laser light can damage your eyes.

WARNING: DO NOT use tinted glasses to enhance the laser light. Tinted glasses will reduce overall vision for the application and interfere with the normal operation of the tool.

INSTALLING THE BATTERIES (FIG. D)

Detach the laser from the jig saw by removing the screw (16) and pulling laser (10) forward. Insert 2 fresh 1.5 volt AAA batteries making sure to match (+) and (-) terminals correctly. Reattach the laser.

WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk:

Carefully follow all instructions and warnings on the battery label and package.

Always insert batteries correctly with regard to polarity (+ and -), marked on the battery and the equipment.

Do not short battery terminals.

Do not charge batteries.

Do not mix old and new batteries. Replace all of them at the same time with new batteries of the same brand and type.

Remove dead batteries immediately and dispose of per local codes.

Do not dispose of batteries in fire.

Keep batteries out of reach of children.

“Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.”

SWITCHING THE LASER ON AND OFF (FIG. D)

To turn the laser on, press in on the on/off button (17). To turn the laser off, press the button a second time. The laser button is “on” when subflush to the housing, and “off” when the laser button is flush.

ADJUSTING THE LASER SIDE TO SIDE (FIG. E)

NOTE: Laser is intended to be a cutting aid and does not guarantee a precise cut. Use laser adjustment screw (18) to align laser line with saw blade if needed.

WARNING: Laceration Hazard: DO NOT adjust the laser when the jig saw is plugged in.

WARNING: Laser circuit will reduce output visibility (power) of laser when overheated. Laser may be not visible when saw is overloaded for prolonged period of time. Laser visibility (power) will gradually return back to normal when tool cools down even if the tool is unplugged.

WARNING: Do not leave overheated laser ON unattended. Make sure the switch is in the OFF position as shown in the inset of figure D. Remove the batteries to cut power

to the laser.

Hints for Optimum Use

GENERAL

-Use a high speed for wood, a medium speed for aluminum and PVC and a low speed for metals other than aluminum.

8

Image 8
Contents Orbital Action JigSaw with Laser VEA EL Español EN LA ContraportadaPersonal Safety Work Area SafetyElectrical Safety Service Specific Safety RulesPower Tool USE and Care Safety Instructions Lasers Features JS650L ON/OFF1053 AM Assembly Operating the JIG SAWHints for Optimum Use Operating the LaserTroubleshooting MaintenanceAccessories Sawing LaminatesService Information Full TWO-YEAR Home USE Warranty Technical Specifications of LaserMode D’EMPLOI Sécurité DU Lieu DE Travail Sécurité EN Matière D’ÉLECTRICITÉSécurité Personnelle Utilisation ET Entretien D’UN Outil ÉlectriqueRègles de sécurité spécifiques RéparationCaractéristiques du modèle JS650L Directives DE Sécurité Pour LasersON/OFF Moteur Conserver CES Directives AssemblageUtilisation DE LA Scie Sauteuse Utilisation DU LaserRéglage DU Laser Pour Action Latérale FIG. E Insertion DES Piles FIG. DMise EN MARCHE/ARRÊT DU Laser FIG. D Conseils pour une utilisation optimale DépannageAccessoires Information SUR LES Réparations555326-7100 Seguridad Eléctrica Normas generales de seguridadSeguridad EN EL Área DE Trabajo Seguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaNormas de seguridad específicas MantenimientoCaracterísticas JS650L Instrucciones DE Seguridad Para EL LáserConserve Estas Instrucciones Ensamblaje Inserción DE LA Hoja DE LA Sierra FIG. aUSO DE LA Sierra Caladora USO DEL LáserConsejos para un uso óptimo Apagado Y Encendido DEL Láser FIG. DAjuste DEL Láser DE Lado a Lado FIG. E Aserrado DE LaminadosDetección DE Problemas AccesoriosHasta 152 mm 6 pulgadas de alcance de CULIACAN, SIN MONTERREY, N.L GUADALAJARA, JALPUEBLA, PUE MEXICO, D.F90501515 JS650L 4/5/06 1053 AM