Toshiba RAS-10SKX, RAS-10SAX, RAS-10SK-E Auto Restart Function, How to Set the Auto Restart

Page 16

7-7. Auto Restart Function

This unit is equipped with an Automatic restarting facility which allows the unit to restart and resume the set operating conditions in the event of a power supply shutdown without the use of the hand control.

The operation will resume without warning three minutes after the power is restored.

The Auto Restart function is set not to work on shipment from the factory, and so it is necessary to set it to function as required.

• When the system is stand-by (not running)

7-7-1. How to Set the Auto Restart

To set the Auto Restart function, proceed as follows: Access the TEMPORARY button located in the lower right hand corner beneath the hinged front panel of the indoor unit (please refer to section on PARTS NAME). The power supply to the unit must be on - the function will not be set if the power is off.

To enable the Auto Restart function, press the TEMPORARY button continuously for three seconds. The unit will acknowledge the setting and beep three times. The system will now restart automatically.

The above Auto Restart settings can be carried out:

OPERATION

 

MOTION

 

 

 

 

Press the TEMPORARY button

Stand-by

 

continuously more than three

 

seconds.

The system starts to operate.

The green light will be lit.

 

 

 

 

about three seconds after

0

The unit beeps three times.

The orange light will be lit.

 

3S

 

 

 

 

TEMPORARY

The system is operating.

The orange light is lighting.

 

 

 

 

If the system is not required to run at this time, press the TEMPORARY

 

 

button once more or use the remote control and the unit will stop.

 

 

 

 

• When the system is operating

 

 

 

 

 

 

OPERATION

 

MOTION

 

 

 

 

Press the TEMPORARY button

Operating

The green light is lit.

continuously more than three

 

seconds.

The system stops to operate.

The green light is turned off.

 

 

 

 

about three seconds after

0The unit beeps three times.

3S

 

 

The system stops.

TEMPORARY

 

 

If the system is not required to stop at this time, use the remote control

 

and to restart.

During subsequent operation, the orange light is lit.

The Auto Restart function will not accept an instruction if timer operation with the remote control is selected.

(Please refer to the section on setting the timer or setting the louver.)

During louver swing (AUTO) operation, after restart by the Auto Restart function the louver swing stops.

– 16 –

Image 16
Contents R C O Contents What to be Prechecked First Troubleshooting FlowchartsPrimary Judgement of Trouble Sources Specifications RAS-10SK-E/10SA-E RAS-10SKX/10SAX CoolingCondition JIS C9612-1994 Temperature Cooling Construction Views Indoor UnitOutdoor Unit RAS-10SA-E RAS-10SAXWiring Diagram Main P.C. BoardSpecifications of Electrical Parts Parts name Type SpecificationsRefrigerant Cycle Diagram RAS-10SK-E / RAS-10SA-E RAS-10SKX / RAS-10SAXMICRO-COMPUTER Block Diagram AUTO, COOL, DRY, FAN onlyOperation Descriptions FAN only OperationCool Operation M3/hDRY Operation Louver ControlAuto Operation Temporary AutoLow-Temperature Limit Control Cooling Operation ECONO. ModeCooling How to Set the Auto Restart Auto Restart FunctionHow to Cancel the Auto Restart Case of Power Failure during the Timer OperationInstallation Procedure Safety Cautions For general public useUK Plugs and Sockets etc Safety Regulations SI Number Installation Diagram of Indoor and Outdoor Units AttachInstallation Parts InstallationOptional Parts Installation place Cutting a Hole and Mounting Installation PlateRemote control Mounting the installation plateWhen the installation plate is directly mounted on the wall Electrical WorkWiring Connection How to remove the front cabinetHow to open the screw cap Taking out the power cordStripping length of connecting cable How to install the front cabinet on the indoor unitPiping and Drain Hose Installation Case of rightward pipingCase of downward piping Left-hand connection with pipingIndoor Unit Installation DrainageStrong wind Refrigerant Piping Connection Vacuum PumpingFlaring Tightening connectionPacked Valve Handling Precautions A5 mm hexagon wrench is requiredAuto Restart Setting How to set the Auto RestartOthers Gas Leak TestTroubleshooting Chart Power Supply VoltageWhat to be Prechecked First Incorrect Cable Connection between Indoor and Outdoor UnitsMisleading but Good Operations Program Controlled Operation Operation of air-conditioner DescriptionRole of Indoor Unit Controller Primary Judgement of Trouble SourcesBlock display Self-diagnosis with remote control Selecting ordinary modeSelf-diagnosis by check codes Operating key Indication after operationCondition Code Status Power can not be Turned on No Operation at All Troubleshooting FlowchartsPreliminary checks Checking Procedure Power can not be Turned on after Replacing Indoor PC BoardOutdoor Unit does not Operate Only Compressor does not Operate Only Outdoor Fan does not Operate Check procedure Only the Indoor Fan does not OperateThere is no beep from How to Check the PC Board Operating precautionsInspection procedures Main PC board partProcedure Check Point Symptom Causes PC Board Layout Top View Bottom ViewHow to Reduce the Operation Time of the Anti-Restart Timer SensorPart Replacement Indoor Unit RAS-10SK-E, RAS-10SKXPart name Procedure Remarks Microcomputer RAS-10SK-E, RAS-10SKX Outdoor Unit RAS-10SA-E, RAS-10SAX OFF Exploded Views and Parts List Part DescriptionIndoor Unit Capillary Tube