HP 8000 tower manual Power Management, Smart Cover Lock Optional, ACPI Wake-Up Events

Page 46
Smart Cover Lock (Optional)

System Support

Level 0—Cover removal indication is essentially disabled at this level. During POST, status bit is cleared and no other action is taken by BIOS.

Level 1—During POST the message “The computer's cover has been removed since the last system start up” is displayed and time stamp in CMOS is updated.

Level 2—During POST the “The computer's cover has been removed since the last system start up” message is displayed, time stamp in CMOS is updated, and the user is prompted for the administrator password. (A Setup password must be enabled in order to see this option).

Smart Cover Lock (Optional)

The SFF and CMT systems support an optional solenoid-operated locking bar that, when activated, prevents the cover (hood) from being removed. The GPIO ports 44 and 45 of the SIO controller provide the lock and unlock signals to the solenoid. A locked hood may be bypassed by removing special screws that hold the locking mechanism in place. The special screws are removed with the Smart Cover Lock Failsafe Key.

4.5.2 Power Management

These systems provide baseline hardware support of ACPI- and APM-compliant firmware and software. Key power-consuming components (processor, chipset, I/O controller, and fan) can be placed into a reduced power mode either automatically or by user control. The system can then be brought back up (“wake-up”) by events defined by the ACPI 2.0 specification. The ACPI wake-up events supported by this system are listed as follows:

Table 4-7.

ACPI Wake-Up Events

ACPI Wake-Up Event

System Wakes From

 

 

Power Button

Suspend or soft-off

 

 

RTC Alarm

Suspend or soft-off

 

 

Wake On LAN (w/NIC)

Suspend or soft-off

 

 

PME

Suspend or soft-off

 

 

Serial Port Ring

Suspend or soft-off

 

 

USB

Suspend only

 

 

Keyboard

Suspend only

 

 

Mouse

Suspend only

 

 

 

4-12

www.hp.com

Technical Reference Guide

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Document Part Number Technical Reference GuideHP Compaq 8000 Elite Series Business Desktop Computers DecemberHP Compaq 8000 Elite Series Business Desktop Computers Technical Reference GuideFirst Edition December Document Part Number 1 Introduction Contents2 System Overview 4 System Support 3 Processor/Memory Subsystem5 Input/Output Interfaces 7 Power and Signal Distribution 6 Integrated Graphics Subsystem8 SYSTEM BIOS A Error Messages and Codes Index1.2 Additional Information Sources Introduction1.1 About this Guide 1.1.1 Online Viewing1.4.1 Special Notices 1.3 Serial Number1.4 Notational Conventions 1.4.2 ValuesAcronym or 1.5 Common Acronyms and AbbreviationsAcronyms and Abbreviations AbbreviationTable 1-1 Continued Acronym or Table 1-1 ContinuedAcronyms and Abbreviations AbbreviationAcronym or Table 1-1 ContinuedAcronyms and Abbreviations AbbreviationAcronym or Table 1-1 ContinuedAcronyms and Abbreviations AbbreviationAcronym or Table 1-1 ContinuedAcronyms and Abbreviations AbbreviationAcronym or 1-10 System Overview 2.1 Introduction2.2 Features Feature Differences by Form Factor USDT2.3 System Architecture Architectural Differences by Form FactorSystem Overview 2.3.2 Chipset 2.3.1 Intel Processor SupportChipset Components and Functionality 2.3.4 System Memory 2.3.3 Support ComponentsSupport Component Functions 2.3.7 Universal Serial Bus Interface 2.3.5 Mass Storage2.3.6 Serial Interface 2.3.8 Network Interface Controller2.3.10 Audio Subsystem 2.3.9 Graphics SubsystemIntegrated Graphics Subsystem Statistics 2.3.11 HP ProtectTools Embedded Security 2.4 SpecificationsEnvironmental Specifications Factory Configuration Power Supply Electrical Specifications Physical Specifications2-12 Processor/Memory Subsystem 3.1 Introduction3.2 Intel Processors 3.2.1 Intel Processor Overview3.2.2 Processor Changing/Upgrading Supported Processors partial listing3.3 Memory Subsystem 3.3.2 Memory Mapping and Pre-allocation 3.3.1 Memory UpgradingMemory Socket Loading Expansion Area Figure 3-2. System Memory Map for maximum of 8 gigabytesBase Memory 4.2 PCI Bus Overview System Support4.1 Introduction 4.2.1 PCI 2.3 Bus OperationSystem Support PCI Component Configuration AccessWired to PCI BusTransaction Protocol Layer 4.2.2 PCI Express Bus OperationSoftware/Driver Layer PCI Bus Mastering Devices4.2.4 PCI Interrupts 4.2.5 PCI Power Management Support4.2.3 Option ROM Mapping Link LayerPCI 2.3 Bus Connector Pinout 4.2.6 PCI ConnectorsPCI 2.3 Connector Figure 4-2. 32-bit, 5.0-volt PCI 2.3 Bus ConnectorPCIe Bus Connector Pinout PCIe ConnectorsFigure 4-3. PCIe Bus Connectors 8259 Mode 4.3 System Resources4.3.1 Interrupts APIC Mode4.3.2 Direct Memory Access PCI Interrupt Distribution4.4 Real-Time Clock and Configuration Memory 4.4.1 Clearing CMOS4.5.1 Security Functions 4.5 System Management4.4.2 Standard CMOS Locations Configuration Memory CMOS MapCable Lock Provision Power-On / Setup PasswordSetup Password I/O Interface SecuritySmart Cover Lock Optional 4.5.2 Power ManagementACPI Wake-Up Events 4.5.4 Thermal Sensing and Cooling 4.5.3 System StatusSystem Operational Status LED Indications 4.6 Register Map and Miscellaneous Functions 4.6.1 System I/O MapI/O Port System I/O MapFunction ICH10 Functions 4.6.2 GPIO FunctionsSIO Controller Functions Input/Output Interfaces 5.1 Introduction5.2 SATA/eSATA Interfaces 5.2.1 SATA interface5.2.2 eSATA interface 5.3 Serial Interface DB-9 Serial Connector Pinout5.4.2 Enhanced Parallel Port Mode 5.4 Parallel Interface Support5.4.1 Standard Parallel Port Mode 5.4.3 Extended Capabilities Port ModeDB-25 Parallel Connector Pinout 5.4.4 Parallel Interface Connectore w q - 9 8 7 6 5 4 3 2 1 g f d s a p o i u y t r 5.5 Keyboard/Pointing Device Interface 5.5.1 Keyboard Interface Operation5.5.2 Pointing Device Interface Operation 5.5.3 Keyboard/Pointing Device Interface ConnectorKeyboard/Pointing Device Connector Pinout 5.6.1 USB Connector 5.6 Universal Serial Bus InterfaceUSB Cable Length Data 5.6.2 USB Cable DataUSB Connector Pinout USB Color Code5.7 Audio Subsystem Figure 5-8. Audio Subsystem Functional Block Diagram5.7.2 HD Audio Link Bus 5.7.1 HD Audio Controller5.7.3 Audio Multistreaming The specifications for the HD Audio subsystem are listed in Table 5.7.4 Audio SpecificationsHD Audio Subsystem Specifications 5.8 Network Interface Controller 5.8.1 Wake-On-LAN Support 5.8.3 Power Management Support5.8.2 Alert Standard Format Support 5.8.5 NIC Specifications 5.8.4 NIC ConnectorTable 5-11. NIC Specifications Integrated Graphics Subsystem 6.1 Introduction6.2 Functional Description GMA 4500 Memory Allocation SDRAM InstalledMaximum Memory Allocation 6.3 Display Modes 6.4 Upgrading 6.5 Monitor Connectors 6.5.1 Analog Monitor Connector6.5.2 DisplayPort Connector Figure 6-3. DisplayPort Connector, as viewed from rear of chassisIntegrated Graphics Subsystem 7.2 USDT Power Distribution Power and Signal Distribution7.1 Introduction USDT 135-Watt Power Supply Unit Specifications 7.3 SFF/CMT Power DistributionTable 7-1 lists the specifications of the external supply Figure 7-2. SFF/CMT Power Distribution and Cabling, Block DiagramSFF 240-Watt Power Supply Unit Specifications CMT 320-Watt Power Supply Unit Specifications7.4 Power Control 7.4.1 Power ButtonPower failure power supply is overloaded. Check storage Power LED IndicationsPower LED Pre-video memory error. Incompatible or incorrectly seatedPower Management Event 7.5 Power Management7.4.2 Wake Up Events Wake-On-LANPower System Power StatesPower StateDesignator 7.6 Signal DistributionSystem Board Connector, Indicator, and Switch Designations Component functionTable 7-7. Continued Figure 7-5 shows pinouts of headers used on the sytem boardsFigure 7-3. System Board Header Pinouts 7-10 System BIOS 8.1 Introduction8.2.1 Upgrading 8.2 ROM Flashing8.2.2 Changeable Splash Screen 8.3.2 Network Boot F12 Support 8.3 Boot Functions8.3.1 Boot Device Order 8.3.3 Memory Detection and Configuration8.3.4 Boot Error Codes 8.4 Client Management Functions 8.4.2 Temperature Status 8.4.1 System ID and ROM TypeSystem ID Numbers 8.5 SMBIOS SMBIOS Functions8.6 USB Legacy Support 8.7 Management Engine FunctionsA.2 Beep/Power LED Codes Error Messages and CodesA.1 Introduction A.3 Power-On Self Test POST Messages Error Messages and Codes1794--Inaccessible device attached to SATA Power-On Self Test POST MessagesError Message 1796-SATA Cabling Error1801-Microcode Patch Error A.4 System Error Messages Error Messages and CodesMemory Error Messages A.5 Memory Error MessagesTable A-4 Table A-4. Continued A.6 Keyboard Error MessagesMemory Error Messages MessageInt. test, LpBk. test., and data register failed A.7 Printer Error MessagesA.8 Video Graphics Error Messages Int. test, LpBk. test., and cntrl. register failedA.9 Diskette Drive Error Messages A.10 Serial Interface Error Messages Table A-9 Serial Interface Error MessagesA.11 Modem Communications Error Messages Table A-10 Modem Communications Error MessagesA.12 System Status Error Messages A.13 Hard Drive Error Messages Cntlr. failed to deallocate bad sectorsxx = 00, Hard drive ID test xx = 01, Hard drive format test A.14 Hard Drive Error Messages EGA Mono. graphics mode test failed A.15 Video Graphics Error MessagesA.16 Audio Error Messages Lightpen graphics test failed, no respA.17 DVD/CD-ROM Error Messages A.18 Network Interface Error MessagesMessage A.19 SCSI Interface Error Messages 65xx-xx, 66xx-xxProbable Cause A.20 Pointing Device Interface Error Messages 8601-xx A-20 Index Numerics
Related manuals
Manual 18 pages 10.45 Kb Manual 29 pages 22.5 Kb Manual 1 pages 60.13 Kb
Top Page Image Contents