HP 8000 tower manual Table A-2. Continued, Power-On Self Test POST Messages, Error Message

Page 95

Table A-2. (Continued)

Error Messages and Codes

	Table A-2. (Continued)
Power-On Self Test (POST) Messages

Error Message	Probable Cause

514-CPU or Chassis Fan not	CPU fan is not connected or may have malfunctioned.
detected.

601-Diskette Controller Error	Diskette drive removed since previous boot.

605-Diskette Drive Type Error	Mismatch in drive type.

912-Computer Cover Removed	Cover (hood) removal has been detected by the Smart Cover Sensor.
Since Last System Start Up

914-Hood Lock Coil is not	Smart Cover Lock mechanism is missing or not connected.
Connected

916-Power Button Not Connected	Power button harness has been detached or unseated from the system
	board.

917-Expansion Riser Not Detected	Expansion (backplane) board not seated properly.

919-Front Panel, MultiPort, and/or	Riser card has been removed or has not been reinstalled properly in
MultiBay Risers not Detected	the system.

1156-Serial Port A Cable Not	Cable from serial port header to I/O connector is missing or not
Detected	connected properly.

1157-Front Cables Not Detected	Cable from front panel USB and audio connectors is missing or not
	connected properly.

1720-SMART Hard Drive Detects	SMART circuitry on an IDE drive has detected possible equipment
Imminent Failure	failure.

1721-SMART SCSI Hard Drive	SMART circuitry on a SCSI drive has detected possible equipment
Detects Imminent Failure	failure.

1785-MultiBay incorrectly installed	For integrated MultiBay/ USDT systems:
	MultiBay device not properly seated.

or

MultiBay riser not properly seated.

1794--Inaccessible device attached to SATA 1

(for systems with 2 SATA ports)

A device is attached to SATA 1. Any device attached to this connector will be inaccessible while “SATA Emulation” is set to “Combined IDE Controller” in Computer Setup.

1794-Inaccessible devices attached to SATA 1 and/or SATA 5 (for systems with 4 SATA ports)

A device is attached to SATA 1 and/or SATA 5.

Devices attached to these connectors will be inaccessible while “SATA Emulation” is set to “Combined IDE Controller” in Computer Setup

1796-SATA Cabling Error	One or more SATA devices are improperly attached. For optimal
	performance, the SATA 0 and SATA 1 connectors must be used before
	SATA 2 and SATA 3.

Technical Reference Guide

www.hp.com

A-3

Image 95

Contents December Technical Reference GuideHP Compaq 8000 Elite Series Business Desktop Computers Document Part NumberFirst Edition December Document Part Number Technical Reference GuideHP Compaq 8000 Elite Series Business Desktop Computers 2 System Overview Contents1 Introduction 5 Input/Output Interfaces 3 Processor/Memory Subsystem4 System Support 6 Integrated Graphics Subsystem 7 Power and Signal DistributionA Error Messages and Codes Index 8 SYSTEM BIOS1.1.1 Online Viewing Introduction1.1 About this Guide 1.2 Additional Information Sources1.4.2 Values 1.3 Serial Number1.4 Notational Conventions 1.4.1 Special NoticesAbbreviation 1.5 Common Acronyms and AbbreviationsAcronyms and Abbreviations Acronym orTable 1-1 Continued Abbreviation Table 1-1 ContinuedAcronyms and Abbreviations Acronym orAbbreviation Table 1-1 ContinuedAcronyms and Abbreviations Acronym orAbbreviation Table 1-1 ContinuedAcronyms and Abbreviations Acronym orAbbreviation Table 1-1 ContinuedAcronyms and Abbreviations Acronym orAbbreviation 1-10 2.1 Introduction System Overview2.2 Features USDT Feature Differences by Form FactorArchitectural Differences by Form Factor 2.3 System ArchitectureTechnical Reference Guide Chipset Components and Functionality 2.3.1 Intel Processor Support2.3.2 Chipset Support Component Functions 2.3.3 Support Components2.3.4 System Memory 2.3.8 Network Interface Controller 2.3.5 Mass Storage2.3.6 Serial Interface 2.3.7 Universal Serial Bus InterfaceIntegrated Graphics Subsystem Statistics 2.3.9 Graphics Subsystem2.3.10 Audio Subsystem Environmental Specifications Factory Configuration 2.4 Specifications2.3.11 HP ProtectTools Embedded Security Physical Specifications Power Supply Electrical Specifications2-12 3.1 Introduction Processor/Memory Subsystem3.2.1 Intel Processor Overview 3.2 Intel ProcessorsSupported Processors partial listing 3.2.2 Processor Changing/Upgrading3.3 Memory Subsystem Memory Socket Loading 3.3.1 Memory Upgrading3.3.2 Memory Mapping and Pre-allocation Base Memory Figure 3-2. System Memory Map for maximum of 8 gigabytesExpansion Area 4.2.1 PCI 2.3 Bus Operation System Support4.1 Introduction 4.2 PCI Bus OverviewPCI Bus PCI Component Configuration AccessWired to System SupportPCI Bus Mastering Devices 4.2.2 PCI Express Bus OperationSoftware/Driver Layer Transaction Protocol LayerLink Layer 4.2.5 PCI Power Management Support4.2.3 Option ROM Mapping 4.2.4 PCI InterruptsFigure 4-2. 32-bit, 5.0-volt PCI 2.3 Bus Connector 4.2.6 PCI ConnectorsPCI 2.3 Connector PCI 2.3 Bus Connector PinoutFigure 4-3. PCIe Bus Connectors PCIe ConnectorsPCIe Bus Connector Pinout APIC Mode 4.3 System Resources4.3.1 Interrupts 8259 ModePCI Interrupt Distribution 4.3.2 Direct Memory Access4.4.1 Clearing CMOS 4.4 Real-Time Clock and Configuration MemoryConfiguration Memory CMOS Map 4.5 System Management4.4.2 Standard CMOS Locations 4.5.1 Security FunctionsI/O Interface Security Power-On / Setup PasswordSetup Password Cable Lock ProvisionACPI Wake-Up Events 4.5.2 Power ManagementSmart Cover Lock Optional System Operational Status LED Indications 4.5.3 System Status4.5.4 Thermal Sensing and Cooling 4.6.1 System I/O Map 4.6 Register Map and Miscellaneous FunctionsFunction System I/O MapI/O Port SIO Controller Functions 4.6.2 GPIO FunctionsICH10 Functions 5.1 Introduction Input/Output Interfaces5.2.1 SATA interface 5.2 SATA/eSATA Interfaces5.2.2 eSATA interface DB-9 Serial Connector Pinout 5.3 Serial Interface5.4.3 Extended Capabilities Port Mode 5.4 Parallel Interface Support5.4.1 Standard Parallel Port Mode 5.4.2 Enhanced Parallel Port Modee w q - 9 8 7 6 5 4 3 2 1 g f d s a p o i u y t r 5.4.4 Parallel Interface ConnectorDB-25 Parallel Connector Pinout 5.5.1 Keyboard Interface Operation 5.5 Keyboard/Pointing Device InterfaceKeyboard/Pointing Device Connector Pinout 5.5.3 Keyboard/Pointing Device Interface Connector5.5.2 Pointing Device Interface Operation 5.6 Universal Serial Bus Interface 5.6.1 USB ConnectorUSB Color Code 5.6.2 USB Cable DataUSB Connector Pinout USB Cable Length DataFigure 5-8. Audio Subsystem Functional Block Diagram 5.7 Audio Subsystem5.7.3 Audio Multistreaming 5.7.1 HD Audio Controller5.7.2 HD Audio Link Bus HD Audio Subsystem Specifications 5.7.4 Audio SpecificationsThe specifications for the HD Audio subsystem are listed in Table 5.8 Network Interface Controller 5.8.2 Alert Standard Format Support 5.8.3 Power Management Support5.8.1 Wake-On-LAN Support Table 5-11. NIC Specifications 5.8.4 NIC Connector5.8.5 NIC Specifications 6.1 Introduction Integrated Graphics Subsystem6.2 Functional Description Maximum Memory Allocation SDRAM InstalledGMA 4500 Memory Allocation 6.3 Display Modes 6.4 Upgrading 6.5.1 Analog Monitor Connector 6.5 Monitor ConnectorsFigure 6-3. DisplayPort Connector, as viewed from rear of chassis 6.5.2 DisplayPort ConnectorTechnical Reference Guide 7.1 Introduction Power and Signal Distribution7.2 USDT Power Distribution Figure 7-2. SFF/CMT Power Distribution and Cabling, Block Diagram 7.3 SFF/CMT Power DistributionTable 7-1 lists the specifications of the external supply USDT 135-Watt Power Supply Unit SpecificationsCMT 320-Watt Power Supply Unit Specifications SFF 240-Watt Power Supply Unit Specifications7.4.1 Power Button 7.4 Power ControlPre-video memory error. Incompatible or incorrectly seated Power LED IndicationsPower LED Power failure power supply is overloaded. Check storageWake-On-LAN 7.5 Power Management7.4.2 Wake Up Events Power Management EventState System Power StatesPower PowerComponent function 7.6 Signal DistributionSystem Board Connector, Indicator, and Switch Designations DesignatorFigure 7-3. System Board Header Pinouts Figure 7-5 shows pinouts of headers used on the sytem boardsTable 7-7. Continued 7-10 8.1 Introduction System BIOS8.2.2 Changeable Splash Screen 8.2 ROM Flashing8.2.1 Upgrading 8.3.3 Memory Detection and Configuration 8.3 Boot Functions8.3.1 Boot Device Order 8.3.2 Network Boot F12 Support8.3.4 Boot Error Codes 8.4 Client Management Functions System ID Numbers 8.4.1 System ID and ROM Type8.4.2 Temperature Status SMBIOS Functions 8.5 SMBIOS8.7 Management Engine Functions 8.6 USB Legacy SupportA.1 Introduction Error Messages and CodesA.2 Beep/Power LED Codes Error Messages and Codes A.3 Power-On Self Test POST Messages1796-SATA Cabling Error Power-On Self Test POST MessagesError Message 1794--Inaccessible device attached to SATA1801-Microcode Patch Error Error Messages and Codes A.4 System Error MessagesTable A-4 A.5 Memory Error MessagesMemory Error Messages Message A.6 Keyboard Error MessagesMemory Error Messages Table A-4. ContinuedInt. test, LpBk. test., and cntrl. register failed A.7 Printer Error MessagesA.8 Video Graphics Error Messages Int. test, LpBk. test., and data register failedA.9 Diskette Drive Error Messages Table A-9 Serial Interface Error Messages A.10 Serial Interface Error MessagesTable A-10 Modem Communications Error Messages A.11 Modem Communications Error MessagesA.12 System Status Error Messages Cntlr. failed to deallocate bad sectors A.13 Hard Drive Error Messagesxx = 00, Hard drive ID test xx = 01, Hard drive format test A.14 Hard Drive Error Messages Lightpen graphics test failed, no resp A.15 Video Graphics Error MessagesA.16 Audio Error Messages EGA Mono. graphics mode test failedA.18 Network Interface Error Messages A.17 DVD/CD-ROM Error MessagesProbable Cause A.19 SCSI Interface Error Messages 65xx-xx, 66xx-xxMessage A.20 Pointing Device Interface Error Messages 8601-xx A-20 Numerics Index

Related manuals

Manual 18 pages 10.45 Kb

Manual 29 pages 22.5 Kb

Manual 1 pages 60.13 Kb