HP 8000 tower manual Wake-On-LAN Support, Alert Standard Format Support, Power Management Support

Page 65
5.8.1Wake-On-LAN Support

Input/Output Interfaces

✎For the features in the following paragraphs to function as described, the system unit must be plugged into a live AC outlet. Controlling unit power through a switchable power strip will, with the strip turned off, disable any wake, alert, or power mangement functionality.

5.8.1Wake-On-LAN Support

The NIC supports the Wired-for-Management (WfM) standard of Wake-On-LAN (WOL) that allows the system to be booted up from a powered-down or low-power condition upon the detection of special packets received over a network. The detection of a Magic Packet by the NIC results in the PME- signal on the PCI bus to be asserted, initiating system wake-up from an ACPI S1 or S3 state.

5.8.2 Alert Standard Format Support

Alert Standard Format (ASF) support allows the NIC to communicate the occurrence of certain events over a network to an ASF 1.0-compliant management console and, if necessary, take action that may be required. The ASF communications can involve the following:

■Alert messages sent by the client to the management console.

■Maintenance requests sent by the management console to the client.

■Description of client's ASF capabilities and characteristics.

The activation of ASF functionality requires minimal intervention of the user and requires only booting a client system connected to a network with an ASF-compliant management console.

5.8.3 Power Management Support

The NIC features Wired-for-Management (WfM) support providing system wake up from network events (WOL) as well as generating system status messages (AOL) and supports ACPI power management environments. The controller receives 3.3 VDC (auxiliary) power as long as the system is plugged into a live AC receptacle, allowing support of wake-up events occurring over a network while the system is powered down or in a low-power state.

The Advanced Configuration and Power Interface (ACPI) functionality of system wake up is implemented through an ACPI-compliant OS and is the default power management mode. The following wakeup events may be individually enabled/disabled through the supplied software driver:

■Magic Packet—Packet with node address repeated 16 times in data portion

✎The following functions are supported in NDIS5 drivers but implemented through remote management software applications (such as LanDesk).

■Individual address match—Packet with matching user-defined byte mask

■Multicast address match—Packet with matching user-defined sample frame

■ARP (address resolution protocol) packet

■Flexible packet filtering—Packets that match defined CRC signature

The PROSet Application software (pre-installed and accessed through the System Tray or Windows Control Panel) allows configuration of operational parameters such as WOL and duplex mode.

 

Technical Reference Guide

www.hp.com

5-15

Page 64 Page 66
Image 65
Page 64 Page 66
Contents HP Compaq 8000 Elite Series Business Desktop Computers Technical Reference GuideDocument Part Number DecemberFirst Edition December Document Part Number Technical Reference GuideHP Compaq 8000 Elite Series Business Desktop Computers 2 System Overview Contents1 Introduction 5 Input/Output Interfaces 3 Processor/Memory Subsystem4 System Support 6 Integrated Graphics Subsystem 7 Power and Signal DistributionA Error Messages and Codes Index 8 SYSTEM BIOS1.1 About this Guide Introduction1.2 Additional Information Sources 1.1.1 Online Viewing1.4 Notational Conventions 1.3 Serial Number1.4.1 Special Notices 1.4.2 ValuesAcronyms and Abbreviations 1.5 Common Acronyms and AbbreviationsAcronym or AbbreviationTable 1-1 Continued Acronyms and Abbreviations Table 1-1 ContinuedAcronym or AbbreviationAcronyms and Abbreviations Table 1-1 ContinuedAcronym or AbbreviationAcronyms and Abbreviations Table 1-1 ContinuedAcronym or AbbreviationAcronyms and Abbreviations Table 1-1 ContinuedAcronym or AbbreviationAcronyms and Abbreviations 1-10 2.1 Introduction System Overview2.2 Features USDT Feature Differences by Form FactorArchitectural Differences by Form Factor 2.3 System ArchitectureTechnical Reference Guide Chipset Components and Functionality 2.3.1 Intel Processor Support2.3.2 Chipset Support Component Functions 2.3.3 Support Components2.3.4 System Memory 2.3.6 Serial Interface 2.3.5 Mass Storage2.3.7 Universal Serial Bus Interface 2.3.8 Network Interface ControllerIntegrated Graphics Subsystem Statistics 2.3.9 Graphics Subsystem2.3.10 Audio Subsystem Environmental Specifications Factory Configuration 2.4 Specifications2.3.11 HP ProtectTools Embedded Security Physical Specifications Power Supply Electrical Specifications2-12 3.1 Introduction Processor/Memory Subsystem3.2.1 Intel Processor Overview 3.2 Intel ProcessorsSupported Processors partial listing 3.2.2 Processor Changing/Upgrading3.3 Memory Subsystem Memory Socket Loading 3.3.1 Memory Upgrading3.3.2 Memory Mapping and Pre-allocation Base Memory Figure 3-2. System Memory Map for maximum of 8 gigabytesExpansion Area 4.1 Introduction System Support4.2 PCI Bus Overview 4.2.1 PCI 2.3 Bus OperationWired to PCI Component Configuration AccessSystem Support PCI BusSoftware/Driver Layer 4.2.2 PCI Express Bus OperationTransaction Protocol Layer PCI Bus Mastering Devices4.2.3 Option ROM Mapping 4.2.5 PCI Power Management Support4.2.4 PCI Interrupts Link LayerPCI 2.3 Connector 4.2.6 PCI ConnectorsPCI 2.3 Bus Connector Pinout Figure 4-2. 32-bit, 5.0-volt PCI 2.3 Bus ConnectorFigure 4-3. PCIe Bus Connectors PCIe ConnectorsPCIe Bus Connector Pinout 4.3.1 Interrupts 4.3 System Resources8259 Mode APIC ModePCI Interrupt Distribution 4.3.2 Direct Memory Access4.4.1 Clearing CMOS 4.4 Real-Time Clock and Configuration Memory4.4.2 Standard CMOS Locations 4.5 System Management4.5.1 Security Functions Configuration Memory CMOS MapSetup Password Power-On / Setup PasswordCable Lock Provision I/O Interface SecurityACPI Wake-Up Events 4.5.2 Power ManagementSmart Cover Lock Optional System Operational Status LED Indications 4.5.3 System Status4.5.4 Thermal Sensing and Cooling 4.6.1 System I/O Map 4.6 Register Map and Miscellaneous FunctionsFunction System I/O MapI/O Port SIO Controller Functions 4.6.2 GPIO FunctionsICH10 Functions 5.1 Introduction Input/Output Interfaces5.2.1 SATA interface 5.2 SATA/eSATA Interfaces5.2.2 eSATA interface DB-9 Serial Connector Pinout 5.3 Serial Interface5.4.1 Standard Parallel Port Mode 5.4 Parallel Interface Support5.4.2 Enhanced Parallel Port Mode 5.4.3 Extended Capabilities Port Modee w q - 9 8 7 6 5 4 3 2 1 g f d s a p o i u y t r 5.4.4 Parallel Interface ConnectorDB-25 Parallel Connector Pinout 5.5.1 Keyboard Interface Operation 5.5 Keyboard/Pointing Device InterfaceKeyboard/Pointing Device Connector Pinout 5.5.3 Keyboard/Pointing Device Interface Connector5.5.2 Pointing Device Interface Operation 5.6 Universal Serial Bus Interface 5.6.1 USB ConnectorUSB Connector Pinout 5.6.2 USB Cable DataUSB Cable Length Data USB Color CodeFigure 5-8. Audio Subsystem Functional Block Diagram 5.7 Audio Subsystem5.7.3 Audio Multistreaming 5.7.1 HD Audio Controller5.7.2 HD Audio Link Bus HD Audio Subsystem Specifications 5.7.4 Audio SpecificationsThe specifications for the HD Audio subsystem are listed in Table 5.8 Network Interface Controller 5.8.2 Alert Standard Format Support 5.8.3 Power Management Support5.8.1 Wake-On-LAN Support Table 5-11. NIC Specifications 5.8.4 NIC Connector5.8.5 NIC Specifications 6.1 Introduction Integrated Graphics Subsystem6.2 Functional Description Maximum Memory Allocation SDRAM InstalledGMA 4500 Memory Allocation 6.3 Display Modes 6.4 Upgrading 6.5.1 Analog Monitor Connector 6.5 Monitor ConnectorsFigure 6-3. DisplayPort Connector, as viewed from rear of chassis 6.5.2 DisplayPort ConnectorTechnical Reference Guide 7.1 Introduction Power and Signal Distribution7.2 USDT Power Distribution Table 7-1 lists the specifications of the external supply 7.3 SFF/CMT Power DistributionUSDT 135-Watt Power Supply Unit Specifications Figure 7-2. SFF/CMT Power Distribution and Cabling, Block DiagramCMT 320-Watt Power Supply Unit Specifications SFF 240-Watt Power Supply Unit Specifications7.4.1 Power Button 7.4 Power ControlPower LED Power LED IndicationsPower failure power supply is overloaded. Check storage Pre-video memory error. Incompatible or incorrectly seated7.4.2 Wake Up Events 7.5 Power ManagementPower Management Event Wake-On-LANPower System Power StatesPower StateSystem Board Connector, Indicator, and Switch Designations 7.6 Signal DistributionDesignator Component functionFigure 7-3. System Board Header Pinouts Figure 7-5 shows pinouts of headers used on the sytem boardsTable 7-7. Continued 7-10 8.1 Introduction System BIOS8.2.2 Changeable Splash Screen 8.2 ROM Flashing8.2.1 Upgrading 8.3.1 Boot Device Order 8.3 Boot Functions8.3.2 Network Boot F12 Support 8.3.3 Memory Detection and Configuration8.3.4 Boot Error Codes 8.4 Client Management Functions System ID Numbers 8.4.1 System ID and ROM Type8.4.2 Temperature Status SMBIOS Functions 8.5 SMBIOS8.7 Management Engine Functions 8.6 USB Legacy SupportA.1 Introduction Error Messages and CodesA.2 Beep/Power LED Codes Error Messages and Codes A.3 Power-On Self Test POST MessagesError Message Power-On Self Test POST Messages1794--Inaccessible device attached to SATA 1796-SATA Cabling Error1801-Microcode Patch Error Error Messages and Codes A.4 System Error MessagesTable A-4 A.5 Memory Error MessagesMemory Error Messages Memory Error Messages A.6 Keyboard Error MessagesTable A-4. Continued MessageA.8 Video Graphics Error Messages A.7 Printer Error MessagesInt. test, LpBk. test., and data register failed Int. test, LpBk. test., and cntrl. register failedA.9 Diskette Drive Error Messages Table A-9 Serial Interface Error Messages A.10 Serial Interface Error MessagesTable A-10 Modem Communications Error Messages A.11 Modem Communications Error MessagesA.12 System Status Error Messages Cntlr. failed to deallocate bad sectors A.13 Hard Drive Error Messagesxx = 00, Hard drive ID test xx = 01, Hard drive format test A.14 Hard Drive Error Messages A.16 Audio Error Messages A.15 Video Graphics Error MessagesEGA Mono. graphics mode test failed Lightpen graphics test failed, no respA.18 Network Interface Error Messages A.17 DVD/CD-ROM Error MessagesProbable Cause A.19 SCSI Interface Error Messages 65xx-xx, 66xx-xxMessage A.20 Pointing Device Interface Error Messages 8601-xx A-20 Numerics Index
Related manuals
Manual 18 pages 10.45 Kb Manual 29 pages 22.5 Kb Manual 1 pages 60.13 Kb
Top Page Image Contents